EN-Product-Metallic coated-Structural steel-S220GD+Z/+ZM TSUK

S220GD+Z/+ZM

Specification details for S220GD+Z/+ZM

EN-Product-Metallic coated-Structural steel-All Grades OverviewTSUK

Overview

Relationship with standards

Galvanised structural steel complies with the following European standard

EN 10346: 2015
Grade
S220GD+Z/+ZM
S250GD+Z/+ZM
S280GD+Z/+ZM
S320GD+Z/+ZM
S350GD+Z/+ZM
S390GD+Z/+ZM
S420GD+Z/+ZM
S450GD+Z/+ZM
S550GD+Z

For products produced in the Netherlands click here.

EN-Product-Metallic coated-All Grades Coatings Surface aspectsTSUK

Coatings and surface aspects

Coatings

Three types of metallic coating are available:

Pure zinc

Galvanised steel (Z/GI) is coated with an almost pure zinc coating (>99% zinc).

Zinc-iron alloy

Produced in the Netherlands. For further information click here.

MagiZinc

MagiZinc steel (ZM) is coated with a zinc coating containing additional magnesium and aluminium.

Coating weight

Coating	Minimum	Maximum
Pure zinc (Z/GI)	90 (6 µm/side)	275 (20 µm/side)
MagiZinc (ZM)¹	70 (5 µm/side)	310 (22 µm/side)

Coating weight measured in g/m² double-sided (µm, per side).

Surface quality

Surface quality complies with standard: EN 10346:2015. Galvanised steels are available in surface quality A, B or C.
Also, Serica FLO^®surface quality produced in the Netherlands. For further information click here.

Surface quality A: as coated surface

Imperfections such as pimples, marks, scratches, pits, variations in surface appearance, dark spots, stripe marks and light passivation stains are permissible.
Stretch levelling breaks or run-off marks may appear. Coil breaks and stretcher strains may also appear.

Surface quality B: improved surface

With this surface quality, small imperfections such as stretch levelling breaks, skin pass marks, slight scratches, indentations, surface structure, zinc run-off marks and light passivation stains are permissible.

Surface quality C: best quality surface

Surface condition C is obtained by skin passing. The controlled surface for the exposed side enables application of a uniform paint finish. The reverse surface has, at least, the characteristics of surface quality B.

Surface finish

Pure zinc

MA: minimised spangle, as coated surface (Z/GI).
MB: minimised spangle, improved surface (Z/GI).
MC: minimised spangle, best quality surface (Z/GI).

MagiZinc^®

A : as coated surface (ZM).
B : improved surface (ZM).
C: best quality surface (ZM).

Surface roughness

Metallic coated steel (with the exception of galvanised steel with standard surface (MA) can be supplied in various grades of roughness – please contact us for more details. If no roughness is specified, roughness will be as shown in the table below.

Roughness Ra (µm)
cut off 0.8mm	cut off 2.5mm
0.6 - 1.9	0.7 - 2.2

Surface treatments

The surface treatments available are O, C and CO.

Oiling (O)

The material surface can be oiled with preservative oil. Other types of oil - for increasing strength or reducing weight – are available to help achieve your optimum performance parameters. Please contact us for details.

Tata Steel offers the following range of oiling levels:

Coating type	Capability
Pure zinc (Z/GI)	0.5 - 1.6 g/m²
MagiZinc^® (ZM)	0.5 - 1.6 g/m²

Other oiling levels are available on request.

Chromium-free passivation (C)

This surface treatment temporarily protects the zinc-coated material against white rust during transportation and storage (not applicable to all qualities and dimensions – please contact us for details).

Chromium-free passivation and oiled (CO)

Please request this combination of surface treatments if you require extra protection against white rust formation (not applicable to all qualities and dimensions – please contact us for details).

T-treatment

Please contact us for further information.

Prime Lubrication Treatment (PLT)

Prime Lubrication Treatment facilitates the manufacturing of stamped components by minimising known issues in stamping and joining.
Currently Under development, please contact us regarding further information

Untreated (U)

Please contact us regarding the availability of untreated coils.

EN-Product-Metallic Coated-Structural steel-S220GD-Properties TSUK

Properties

Mechanical properties

Metallic coated structural steel grades have the following mechanical properties (skin-passed) - these are measured longitudinal to the rolling direction:

EN 10346: 2015	Grade	S220GD+Z/+ZM
Min. yield strength Rp_0.2	N/mm²	220
Min. tensile strength R_m	N/mm²	300
Elongation	%	20

If the yield point is pronounced, the values apply to the upper yield point R_eH.
A range of 140 N/mm² can be expected for tensile strength.
Elongation after fracture uses test piece length L₀ = 80 mm.
For a thickness t ≤ 0.7 mm the minimum elongation after fracture is decreased by 2% and for a thickness t ≤ 0.5mm the minimum elongation after fracture is decreased by 4%.

Chemical composition

Tata Steel supplies the following cast analysis with maximum values unless otherwise shown:

EN 10346: 2015	Grade	S220GD+Z/+ZM
C	Max.	0.20
Mn	Max.	1.70
P	Max.	0.10
S	Max.	0.045
Si	Max.	0.60

All values in weight%.

EN-Product-Metallic Coated-Structural steel-S220GD-Dimensions TSUK

Dimensions

Dimensional capability

Galvanised (+Z) products

Dimensions in mm.

Thickness	Max. width
From - up to	S220GD
0.36 - 0.40	1324
0.40 - 0.55	1375
0.55 - 0.66	1525
0.66 - 0.70	1650
0.70 - 1.60	1750
1.60 - 1.70	1650
1.70 - 1.80	1560
1.80 - 2.00	1500

For widths below 900 mm, please contact us.
For products produced in the Netherlands click here.

MagiZinc^® (+ZM) products

Dimensions in mm.

Thickness	Max. width
From - up to	S220GD
0.60 - 0.66	1525
0.66 - 0.70	1650
0.70 - 1.60	1750
1.60 - 1.70	1650
1.70 - 1.80	1560
1.80 - 2.00	1500

For widths below 900 mm please contact us.
For products produced in the Netherlands click here.

Tolerances

Tolerances comply with standard EN 10143: 2006.
Tighter tolerances are available - please contact us for details.

EN-Product-Metallic Coated-All Grades Shape and Dimensional TolerancesTSUK

Shape and dimensional tolerances

Tolerances on thickness

The tolerances comply with standard EN 10143: 2006.
Tighter tolerances are available on request.
Thickness tolerance availability is shown below:

Thickness tolerance	Availability
Full thickness tolerance	Available
Special thickness tolerance	Available
50% of full thickness tolerance	Refer before ordering

The following tolerances apply to the grades with a minimum value for the yield strength lower than 260N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
> 0.40	≤ 0.60	± 0.04	± 0.05	± 0.06	± 0.035	± 0.040	± 0.045
> 0.60	≤ 0.80	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.80	≤ 1.00	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 1.00	≤ 1.20	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.20	≤ 1.60	± 0.10	± 0.11	± 0.12	± 0.060	± 0.070	± 0.080
> 1.60	≤ 2.00	± 0.12	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 2.00	≤ 2.50	± 0.14	± 0.15	± 0.16	± 0.090	± 0.100	± 0.110
> 2.50	≤ 3.00	± 0.17	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130
> 3.00	≤ 5.00	± 0.20	± 0.20	± 0.21	± 0.15	± 0.16	± 0.17
> 5.00	≤ 6.50	± 0.22	± 0.22	± 0.23	± 0.17	± 0.18	± 0.19

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 260N/mm^² ≤ R_p0.2 < 360N/mm^² and for grades DX51D and S550GD.

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.035	± 0.040	-
> 0.40	≤ 0.60	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.60	≤ 0.80	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.80	≤ 1.00	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.00	≤ 1.20	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.20	≤ 1.60	± 0.11	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 1.60	≤ 2.00	± 0.14	± 0.15	± 0.16	± 0.080	± 0.090	± 0.110
> 2.00	≤ 2.50	± 0.16	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130
> 2.50	≤ 3.00	± 0.19	± 0.20	± 0.20	± 0.130	± 0.140	± 0.150
> 3.00	≤ 5.00	± 0.22	± 0.24	± 0.25	± 0.17	± 0.18	± 0.19
> 5.00	≤ 6.50	± 0.24	± 0.25	± 0.26	± 0.19	± 0.20	± 0.21

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2.For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm

The following tolerances apply to the steel grades with a minimum value for the yield strength 360N/mm² ≤ R_p0.2 ≤ 420N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.040	± 0.045	-
> 0.40	≤ 0.60	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.60	≤ 0.80	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.80	≤ 1.00	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.00	≤ 1.20	± 0.10	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.20	≤ 1.60	± 0.13	± 0.14	± 0.16	± 0.080	± 0.090	± 0.110
> 1.60	≤ 2.00	± 0.16	± 0.17	± 0.19	± 0.090	± 0.110	± 0.120
> 2.00	≤ 2.50	± 0.18	± 0.20	± 0.21	± 0.120	± 0.130	± 0.140
> 2.50	≤ 3.00	± 0.22	± 0.22	± 0.23	± 0.140	± 0.150	± 0.160
> 3.00	≤ 5.00	± 0.22	± 0.24	± 0.25	± 0.17	± 0.18	± 0.19
> 5.00	≤ 6.50	± 0.24	± 0.25	± 0.26	± 0.19	± 0.20	± 0.21

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 420N/mm² < R_p0.2 ≤ 900N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.06	± 0.07	-	± 0.045	± 0.050	-
> 0.40	≤ 0.60	± 0.06	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.60	≤ 0.80	± 0.07	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 0.80	≤ 1.00	± 0.09	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.00	≤ 1.20	± 0.11	± 0.13	± 0.14	± 0.080	± 0.090	± 0.110
> 1.20	≤ 1.60	± 0.15	± 0.16	± 0.18	± 0.090	± 0.110	± 0.120
> 1.60	≤ 2.00	± 0.18	± 0.19	± 0.21	± 0.110	± 0.120	± 0.140
> 2.00	≤ 2.50	± 0.21	± 0.22	± 0.24	± 0.140	± 0.150	± 0.170
> 2.50	≤ 3.00	± 0.24	± 0.25	± 0.26	± 0.170	± 0.180	± 0.190
> 3.00	≤ 5.00	± 0.26	± 0.27	± 0.28	± 0.23	± 0.24	± 0.26
> 5.00	≤ 6.50	± 0.28	± 0.29	± 0.30	± 0.25	± 0.26	± 0.28

_{^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed}
_{over a length of 15 metres.}
_{^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.}

Tolerances on width

The tolerances on width comply with standard EN 10143: 2006
MagiZinc is not included in the standard, but fulfils EN 10143: 2006 requirements.
Tighter tolerances are available on request.

Tolerances in mm.

Nominal width w	Normal tolerances	Special tolerances (S)
600 ≤ w ≤ 1200	+ 5 0	+ 2 0
1200 < w ≤ 1500	+ 6 0	+ 2 0
1500 < w ≤ 1800	+ 7 0	+ 3 0
w > 1800	+ 8 0	+ 3 0

Dimensions and coil weights

Description	Availability
Coil diameter inner	610mm
Coil diameter inner	(508 mm available on request)
Coil diameter outer	10/7 x width max
	1000mm min.
	2500mm max.
Coil weight	30t max.
	Coil weight limited by maximum outer diameter
	Maximum weight allowed by road/rail transport
	Some products may have different coil weight ranges available
	Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
Minimum tonnage per order	Refer to price list for order quantity details
Minimum tonnage per order	Minimum order quantities may apply

EN-Product-Metallic coated-All grades Further processingTSUK

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type	Slitting	Decoiling	Blanking
Thickness range (mm)	0.2 - 7.0	0.3 - 6.0	0.3 - 6.0
Width range (mm)	10 - 2050	50 - 2600	200 - 2600
Length range	-	up to 6m	up to 6m
Locations	UK Ireland Netherlands Germany France Spain Sweden Norway Finland	UK Ireland Netherlands Germany France Spain Sweden Norway Finland	UK Netherlands

For further information please visit our service centre webpages.

EN-Product-Metallic coated-Structural steel-DownloadsTSUK

Download

Download:

EN-Engineering-Brochure-MagiZinc

MagiZinc - Brochure

Brochure

English

MagiZinc for superior corrosion protection

tata-steel-engineering-magizinc-corrosion-protection-brochure-en.pdf13.86 MB

EN-Product-Metallic coated-Structural steel-S250GD+Z/+ZM TSUK

S250GD+Z/+ZM

Specification details for S250GD+Z/+ZM

EN-Product-Metallic coated-Structural steel-All Grades OverviewTSUK

Overview

Relationship with standards

Galvanised structural steel complies with the following European standard

EN 10346: 2015
Grade
S220GD+Z/+ZM
S250GD+Z/+ZM
S280GD+Z/+ZM
S320GD+Z/+ZM
S350GD+Z/+ZM
S390GD+Z/+ZM
S420GD+Z/+ZM
S450GD+Z/+ZM
S550GD+Z

For products produced in the Netherlands click here.

EN-Product-Metallic coated-All Grades Coatings Surface aspectsTSUK

Coatings and surface aspects

Coatings

Three types of metallic coating are available:

Pure zinc

Galvanised steel (Z/GI) is coated with an almost pure zinc coating (>99% zinc).

Zinc-iron alloy

Produced in the Netherlands. For further information click here.

MagiZinc

MagiZinc steel (ZM) is coated with a zinc coating containing additional magnesium and aluminium.

Coating weight

Coating	Minimum	Maximum
Pure zinc (Z/GI)	90 (6 µm/side)	275 (20 µm/side)
MagiZinc (ZM)¹	70 (5 µm/side)	310 (22 µm/side)

Coating weight measured in g/m² double-sided (µm, per side).

Surface quality

Surface quality complies with standard: EN 10346:2015. Galvanised steels are available in surface quality A, B or C.
Also, Serica FLO^®surface quality produced in the Netherlands. For further information click here.

Surface quality A: as coated surface

Imperfections such as pimples, marks, scratches, pits, variations in surface appearance, dark spots, stripe marks and light passivation stains are permissible.
Stretch levelling breaks or run-off marks may appear. Coil breaks and stretcher strains may also appear.

Surface quality B: improved surface

With this surface quality, small imperfections such as stretch levelling breaks, skin pass marks, slight scratches, indentations, surface structure, zinc run-off marks and light passivation stains are permissible.

Surface quality C: best quality surface

Surface condition C is obtained by skin passing. The controlled surface for the exposed side enables application of a uniform paint finish. The reverse surface has, at least, the characteristics of surface quality B.

Surface finish

Pure zinc

MA: minimised spangle, as coated surface (Z/GI).
MB: minimised spangle, improved surface (Z/GI).
MC: minimised spangle, best quality surface (Z/GI).

MagiZinc^®

A : as coated surface (ZM).
B : improved surface (ZM).
C: best quality surface (ZM).

Surface roughness

Metallic coated steel (with the exception of galvanised steel with standard surface (MA) can be supplied in various grades of roughness – please contact us for more details. If no roughness is specified, roughness will be as shown in the table below.

Roughness Ra (µm)
cut off 0.8mm	cut off 2.5mm
0.6 - 1.9	0.7 - 2.2

Surface treatments

The surface treatments available are O, C and CO.

Oiling (O)

The material surface can be oiled with preservative oil. Other types of oil - for increasing strength or reducing weight – are available to help achieve your optimum performance parameters. Please contact us for details.

Tata Steel offers the following range of oiling levels:

Coating type	Capability
Pure zinc (Z/GI)	0.5 - 1.6 g/m²
MagiZinc^® (ZM)	0.5 - 1.6 g/m²

Other oiling levels are available on request.

Chromium-free passivation (C)

This surface treatment temporarily protects the zinc-coated material against white rust during transportation and storage (not applicable to all qualities and dimensions – please contact us for details).

Chromium-free passivation and oiled (CO)

Please request this combination of surface treatments if you require extra protection against white rust formation (not applicable to all qualities and dimensions – please contact us for details).

T-treatment

Please contact us for further information.

Prime Lubrication Treatment (PLT)

Prime Lubrication Treatment facilitates the manufacturing of stamped components by minimising known issues in stamping and joining.
Currently Under development, please contact us regarding further information

Untreated (U)

Please contact us regarding the availability of untreated coils.

EN-Product-Metallic Coated-Structural steel-S250GD-Properties TSUK

Properties

Mechanical properties

Metallic coated structural steel grades have the following mechanical properties (skin-passed) - these are measured longitudinal to the rolling direction:

EN 10346: 2015	Grade	S250GD+Z/+ZM
Min. yield strength Rp_0.2	N/mm²	250
Min. tensile strength R_m	N/mm²	330
Elongation	%	19

If the yield point is pronounced, the values apply to the upper yield point R_eH.
A range of 140 N/mm² can be expected for tensile strength.
Elongation after fracture uses test piece length L₀ = 80 mm.
For a thickness t ≤ 0.7 mm the minimum elongation after fracture is decreased by 2% and for a thickness t ≤ 0.5mm the minimum elongation after fracture is decreased by 4%.

Chemical composition

Tata Steel supplies the following cast analysis with maximum values unless otherwise shown:

EN 10346: 2015	Grade	S250GD+Z/+ZM
C	Max.	0.20
Mn	Max.	1.70
P	Max.	0.10
S	Max.	0.045
Si	Max.	0.60

All values in weight%.

EN-Product-Metallic Coated-Structural steel-S250GD-Dimensions TSUK

Dimensions

Dimensional capability

Galvanised (+Z) products

Dimensions in mm.

Thickness	Max. width
From - up to	S250GD
0.36 - 0.40	1324
0.40 - 0.55	1375
0.55 - 0.60	1520
0.60 - 0.65	1539
0.65 - 0.70	1564
0.70 - 0.75	1650
0.75 - 0.90	1739
0.90 - 1.35	1800
1.35 - 1.50	1764
1.50 - 1.60	1650
1.60 - 1.80	1564
1.80 - 2.00	1539

For widths below 900 mm, please contact us.
For products produced in the Netherlands click here.

MagiZinc^® (+ZM) products

Dimensions in mm.

Thickness	Max. width
From - up to	S250GD
0.60 - 0.65	1539
0.65 - 0.70	1564
0.70 - 0.75	1650
0.70 - 0.90	1739
0.90 - 1.35	1800
1.35 - 1.50	1764
1.50 - 1.60	1650
1.60 - 1.80	1564
1.80 - 2.00	1539

For widths below 900 mm please contact us.
For products produced in the Netherlands click here.

Tolerances

Tolerances comply with standard EN 10143: 2006.
Tighter tolerances are available - please contact us for details.

EN-Product-Metallic Coated-All Grades Shape and Dimensional TolerancesTSUK

Shape and dimensional tolerances

Tolerances on thickness

The tolerances comply with standard EN 10143: 2006.
Tighter tolerances are available on request.
Thickness tolerance availability is shown below:

Thickness tolerance	Availability
Full thickness tolerance	Available
Special thickness tolerance	Available
50% of full thickness tolerance	Refer before ordering

The following tolerances apply to the grades with a minimum value for the yield strength lower than 260N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
> 0.40	≤ 0.60	± 0.04	± 0.05	± 0.06	± 0.035	± 0.040	± 0.045
> 0.60	≤ 0.80	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.80	≤ 1.00	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 1.00	≤ 1.20	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.20	≤ 1.60	± 0.10	± 0.11	± 0.12	± 0.060	± 0.070	± 0.080
> 1.60	≤ 2.00	± 0.12	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 2.00	≤ 2.50	± 0.14	± 0.15	± 0.16	± 0.090	± 0.100	± 0.110
> 2.50	≤ 3.00	± 0.17	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130
> 3.00	≤ 5.00	± 0.20	± 0.20	± 0.21	± 0.15	± 0.16	± 0.17
> 5.00	≤ 6.50	± 0.22	± 0.22	± 0.23	± 0.17	± 0.18	± 0.19

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 260N/mm^² ≤ R_p0.2 < 360N/mm^² and for grades DX51D and S550GD.

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.035	± 0.040	-
> 0.40	≤ 0.60	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.60	≤ 0.80	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.80	≤ 1.00	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.00	≤ 1.20	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.20	≤ 1.60	± 0.11	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 1.60	≤ 2.00	± 0.14	± 0.15	± 0.16	± 0.080	± 0.090	± 0.110
> 2.00	≤ 2.50	± 0.16	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130
> 2.50	≤ 3.00	± 0.19	± 0.20	± 0.20	± 0.130	± 0.140	± 0.150
> 3.00	≤ 5.00	± 0.22	± 0.24	± 0.25	± 0.17	± 0.18	± 0.19
> 5.00	≤ 6.50	± 0.24	± 0.25	± 0.26	± 0.19	± 0.20	± 0.21

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2.For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm

The following tolerances apply to the steel grades with a minimum value for the yield strength 360N/mm² ≤ R_p0.2 ≤ 420N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.040	± 0.045	-
> 0.40	≤ 0.60	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.60	≤ 0.80	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.80	≤ 1.00	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.00	≤ 1.20	± 0.10	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.20	≤ 1.60	± 0.13	± 0.14	± 0.16	± 0.080	± 0.090	± 0.110
> 1.60	≤ 2.00	± 0.16	± 0.17	± 0.19	± 0.090	± 0.110	± 0.120
> 2.00	≤ 2.50	± 0.18	± 0.20	± 0.21	± 0.120	± 0.130	± 0.140
> 2.50	≤ 3.00	± 0.22	± 0.22	± 0.23	± 0.140	± 0.150	± 0.160
> 3.00	≤ 5.00	± 0.22	± 0.24	± 0.25	± 0.17	± 0.18	± 0.19
> 5.00	≤ 6.50	± 0.24	± 0.25	± 0.26	± 0.19	± 0.20	± 0.21

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 420N/mm² < R_p0.2 ≤ 900N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.06	± 0.07	-	± 0.045	± 0.050	-
> 0.40	≤ 0.60	± 0.06	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.60	≤ 0.80	± 0.07	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 0.80	≤ 1.00	± 0.09	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.00	≤ 1.20	± 0.11	± 0.13	± 0.14	± 0.080	± 0.090	± 0.110
> 1.20	≤ 1.60	± 0.15	± 0.16	± 0.18	± 0.090	± 0.110	± 0.120
> 1.60	≤ 2.00	± 0.18	± 0.19	± 0.21	± 0.110	± 0.120	± 0.140
> 2.00	≤ 2.50	± 0.21	± 0.22	± 0.24	± 0.140	± 0.150	± 0.170
> 2.50	≤ 3.00	± 0.24	± 0.25	± 0.26	± 0.170	± 0.180	± 0.190
> 3.00	≤ 5.00	± 0.26	± 0.27	± 0.28	± 0.23	± 0.24	± 0.26
> 5.00	≤ 6.50	± 0.28	± 0.29	± 0.30	± 0.25	± 0.26	± 0.28

_{^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed}
_{over a length of 15 metres.}
_{^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.}

Tolerances on width

The tolerances on width comply with standard EN 10143: 2006
MagiZinc is not included in the standard, but fulfils EN 10143: 2006 requirements.
Tighter tolerances are available on request.

Tolerances in mm.

Nominal width w	Normal tolerances	Special tolerances (S)
600 ≤ w ≤ 1200	+ 5 0	+ 2 0
1200 < w ≤ 1500	+ 6 0	+ 2 0
1500 < w ≤ 1800	+ 7 0	+ 3 0
w > 1800	+ 8 0	+ 3 0

Dimensions and coil weights

Description	Availability
Coil diameter inner	610mm
Coil diameter inner	(508 mm available on request)
Coil diameter outer	10/7 x width max
	1000mm min.
	2500mm max.
Coil weight	30t max.
	Coil weight limited by maximum outer diameter
	Maximum weight allowed by road/rail transport
	Some products may have different coil weight ranges available
	Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
Minimum tonnage per order	Refer to price list for order quantity details
Minimum tonnage per order	Minimum order quantities may apply

EN-Product-Metallic coated-All grades Further processingTSUK

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type	Slitting	Decoiling	Blanking
Thickness range (mm)	0.2 - 7.0	0.3 - 6.0	0.3 - 6.0
Width range (mm)	10 - 2050	50 - 2600	200 - 2600
Length range	-	up to 6m	up to 6m
Locations	UK Ireland Netherlands Germany France Spain Sweden Norway Finland	UK Ireland Netherlands Germany France Spain Sweden Norway Finland	UK Netherlands

For further information please visit our service centre webpages.

EN-Product-Metallic coated-Structural steel-DownloadsTSUK

Download

Download:

EN-Engineering-Brochure-MagiZinc

MagiZinc - Brochure

Brochure

English

MagiZinc for superior corrosion protection

tata-steel-engineering-magizinc-corrosion-protection-brochure-en.pdf13.86 MB

EN-Product-Metallic coated-Structural steel-S280GD+Z/+ZM TSUK

S280GD+Z/+ZM

Specification details for S280GD+Z/+ZM

EN-Product-Metallic coated-Structural steel-All Grades OverviewTSUK

Overview

Relationship with standards

Galvanised structural steel complies with the following European standard

EN 10346: 2015
Grade
S220GD+Z/+ZM
S250GD+Z/+ZM
S280GD+Z/+ZM
S320GD+Z/+ZM
S350GD+Z/+ZM
S390GD+Z/+ZM
S420GD+Z/+ZM
S450GD+Z/+ZM
S550GD+Z

For products produced in the Netherlands click here.

EN-Product-Metallic coated-All Grades Coatings Surface aspectsTSUK

Coatings and surface aspects

Coatings

Three types of metallic coating are available:

Pure zinc

Galvanised steel (Z/GI) is coated with an almost pure zinc coating (>99% zinc).

Zinc-iron alloy

Produced in the Netherlands. For further information click here.

MagiZinc

MagiZinc steel (ZM) is coated with a zinc coating containing additional magnesium and aluminium.

Coating weight

Coating	Minimum	Maximum
Pure zinc (Z/GI)	90 (6 µm/side)	275 (20 µm/side)
MagiZinc (ZM)¹	70 (5 µm/side)	310 (22 µm/side)

Coating weight measured in g/m² double-sided (µm, per side).

Surface quality

Surface quality complies with standard: EN 10346:2015. Galvanised steels are available in surface quality A, B or C.
Also, Serica FLO^®surface quality produced in the Netherlands. For further information click here.

Surface quality A: as coated surface

Imperfections such as pimples, marks, scratches, pits, variations in surface appearance, dark spots, stripe marks and light passivation stains are permissible.
Stretch levelling breaks or run-off marks may appear. Coil breaks and stretcher strains may also appear.

Surface quality B: improved surface

With this surface quality, small imperfections such as stretch levelling breaks, skin pass marks, slight scratches, indentations, surface structure, zinc run-off marks and light passivation stains are permissible.

Surface quality C: best quality surface

Surface condition C is obtained by skin passing. The controlled surface for the exposed side enables application of a uniform paint finish. The reverse surface has, at least, the characteristics of surface quality B.

Surface finish

Pure zinc

MA: minimised spangle, as coated surface (Z/GI).
MB: minimised spangle, improved surface (Z/GI).
MC: minimised spangle, best quality surface (Z/GI).

MagiZinc^®

A : as coated surface (ZM).
B : improved surface (ZM).
C: best quality surface (ZM).

Surface roughness

Metallic coated steel (with the exception of galvanised steel with standard surface (MA) can be supplied in various grades of roughness – please contact us for more details. If no roughness is specified, roughness will be as shown in the table below.

Roughness Ra (µm)
cut off 0.8mm	cut off 2.5mm
0.6 - 1.9	0.7 - 2.2

Surface treatments

The surface treatments available are O, C and CO.

Oiling (O)

The material surface can be oiled with preservative oil. Other types of oil - for increasing strength or reducing weight – are available to help achieve your optimum performance parameters. Please contact us for details.

Tata Steel offers the following range of oiling levels:

Coating type	Capability
Pure zinc (Z/GI)	0.5 - 1.6 g/m²
MagiZinc^® (ZM)	0.5 - 1.6 g/m²

Other oiling levels are available on request.

Chromium-free passivation (C)

This surface treatment temporarily protects the zinc-coated material against white rust during transportation and storage (not applicable to all qualities and dimensions – please contact us for details).

Chromium-free passivation and oiled (CO)

Please request this combination of surface treatments if you require extra protection against white rust formation (not applicable to all qualities and dimensions – please contact us for details).

T-treatment

Please contact us for further information.

Prime Lubrication Treatment (PLT)

Prime Lubrication Treatment facilitates the manufacturing of stamped components by minimising known issues in stamping and joining.
Currently Under development, please contact us regarding further information

Untreated (U)

Please contact us regarding the availability of untreated coils.

EN-Product-Metallic Coated-Structural steel-S280GD-Properties TSUK

Properties

Mechanical properties

Metallic coated structural steel grades have the following mechanical properties (skin-passed) - these are measured longitudinal to the rolling direction:

EN 10346: 2015	Grade	S280GD+Z/+ZM
Min. yield strength Rp_0.2	N/mm²	280
Min. tensile strength R_m	N/mm²	360
Elongation	%	18

If the yield point is pronounced, the values apply to the upper yield point R_eH.
For all grades except S550GD+Z a range of 140 N/mm² can be expected for tensile strength.
Elongation after fracture uses test piece length L₀ = 80 mm.
For a thickness t ≤ 0.7 mm the minimum elongation after fracture is decreased by 2% and for a thickness t ≤ 0.5mm the minimum elongation after fracture is decreased by 4%.

Chemical composition

Tata Steel supplies the following cast analysis with maximum values unless otherwise shown:

EN 10346: 2015	Grade	S280GD+Z/+ZM
C	Max.	0.20
Mn	Max.	1.70
P	Max.	0.10
S	Max.	0.045
Si	Max.	0.60

All values in weight%.

EN-Product-Metallic Coated-Structural steel-S280GD-Dimensions TSUK

Dimensions

Dimensional capability

Galvanised (+Z) products

Dimensions in mm.

Thickness	Max. width
From - up to	S280GD
0.35 - 0.50	1275
0.50 - 0.60	1520
0.60 - 0.66	1525
0.66 - 1.25	1630
1.25 - 1.83	1500
1.83 - 1.91	1445
1.91 - 2.00	1375

For widths below 900 mm, please contact us.
For products produced in the Netherlands click here.

MagiZinc^® (+ZM) products

Dimensions in mm.

Thickness	Max. width
From - up to	S280GD
0.60 - 0.66	1525
0.66 - 1.25	1650
1.25 - 1.83	1520
1.83 - 1.91	1465
1.91 - 2.00	1395

For widths below 900 mm, please contact us.
For products produced in the Netherlands click here.

Tolerances

Tolerances comply with standard EN 10143: 2006.
Tighter tolerances are available - please contact us for details.

EN-Product-Metallic Coated-All Grades Shape and Dimensional TolerancesTSUK

Shape and dimensional tolerances

Tolerances on thickness

The tolerances comply with standard EN 10143: 2006.
Tighter tolerances are available on request.
Thickness tolerance availability is shown below:

Thickness tolerance	Availability
Full thickness tolerance	Available
Special thickness tolerance	Available
50% of full thickness tolerance	Refer before ordering

The following tolerances apply to the grades with a minimum value for the yield strength lower than 260N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
> 0.40	≤ 0.60	± 0.04	± 0.05	± 0.06	± 0.035	± 0.040	± 0.045
> 0.60	≤ 0.80	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.80	≤ 1.00	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 1.00	≤ 1.20	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.20	≤ 1.60	± 0.10	± 0.11	± 0.12	± 0.060	± 0.070	± 0.080
> 1.60	≤ 2.00	± 0.12	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 2.00	≤ 2.50	± 0.14	± 0.15	± 0.16	± 0.090	± 0.100	± 0.110
> 2.50	≤ 3.00	± 0.17	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130
> 3.00	≤ 5.00	± 0.20	± 0.20	± 0.21	± 0.15	± 0.16	± 0.17
> 5.00	≤ 6.50	± 0.22	± 0.22	± 0.23	± 0.17	± 0.18	± 0.19

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 260N/mm^² ≤ R_p0.2 < 360N/mm^² and for grades DX51D and S550GD.

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.035	± 0.040	-
> 0.40	≤ 0.60	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.60	≤ 0.80	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.80	≤ 1.00	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.00	≤ 1.20	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.20	≤ 1.60	± 0.11	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 1.60	≤ 2.00	± 0.14	± 0.15	± 0.16	± 0.080	± 0.090	± 0.110
> 2.00	≤ 2.50	± 0.16	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130
> 2.50	≤ 3.00	± 0.19	± 0.20	± 0.20	± 0.130	± 0.140	± 0.150
> 3.00	≤ 5.00	± 0.22	± 0.24	± 0.25	± 0.17	± 0.18	± 0.19
> 5.00	≤ 6.50	± 0.24	± 0.25	± 0.26	± 0.19	± 0.20	± 0.21

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2.For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm

The following tolerances apply to the steel grades with a minimum value for the yield strength 360N/mm² ≤ R_p0.2 ≤ 420N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.040	± 0.045	-
> 0.40	≤ 0.60	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.60	≤ 0.80	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.80	≤ 1.00	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.00	≤ 1.20	± 0.10	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.20	≤ 1.60	± 0.13	± 0.14	± 0.16	± 0.080	± 0.090	± 0.110
> 1.60	≤ 2.00	± 0.16	± 0.17	± 0.19	± 0.090	± 0.110	± 0.120
> 2.00	≤ 2.50	± 0.18	± 0.20	± 0.21	± 0.120	± 0.130	± 0.140
> 2.50	≤ 3.00	± 0.22	± 0.22	± 0.23	± 0.140	± 0.150	± 0.160
> 3.00	≤ 5.00	± 0.22	± 0.24	± 0.25	± 0.17	± 0.18	± 0.19
> 5.00	≤ 6.50	± 0.24	± 0.25	± 0.26	± 0.19	± 0.20	± 0.21

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 420N/mm² < R_p0.2 ≤ 900N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.06	± 0.07	-	± 0.045	± 0.050	-
> 0.40	≤ 0.60	± 0.06	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.60	≤ 0.80	± 0.07	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 0.80	≤ 1.00	± 0.09	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.00	≤ 1.20	± 0.11	± 0.13	± 0.14	± 0.080	± 0.090	± 0.110
> 1.20	≤ 1.60	± 0.15	± 0.16	± 0.18	± 0.090	± 0.110	± 0.120
> 1.60	≤ 2.00	± 0.18	± 0.19	± 0.21	± 0.110	± 0.120	± 0.140
> 2.00	≤ 2.50	± 0.21	± 0.22	± 0.24	± 0.140	± 0.150	± 0.170
> 2.50	≤ 3.00	± 0.24	± 0.25	± 0.26	± 0.170	± 0.180	± 0.190
> 3.00	≤ 5.00	± 0.26	± 0.27	± 0.28	± 0.23	± 0.24	± 0.26
> 5.00	≤ 6.50	± 0.28	± 0.29	± 0.30	± 0.25	± 0.26	± 0.28

_{^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed}
_{over a length of 15 metres.}
_{^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.}

Tolerances on width

The tolerances on width comply with standard EN 10143: 2006
MagiZinc is not included in the standard, but fulfils EN 10143: 2006 requirements.
Tighter tolerances are available on request.

Tolerances in mm.

Nominal width w	Normal tolerances	Special tolerances (S)
600 ≤ w ≤ 1200	+ 5 0	+ 2 0
1200 < w ≤ 1500	+ 6 0	+ 2 0
1500 < w ≤ 1800	+ 7 0	+ 3 0
w > 1800	+ 8 0	+ 3 0

Dimensions and coil weights

Description	Availability
Coil diameter inner	610mm
Coil diameter inner	(508 mm available on request)
Coil diameter outer	10/7 x width max
	1000mm min.
	2500mm max.
Coil weight	30t max.
	Coil weight limited by maximum outer diameter
	Maximum weight allowed by road/rail transport
	Some products may have different coil weight ranges available
	Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
Minimum tonnage per order	Refer to price list for order quantity details
Minimum tonnage per order	Minimum order quantities may apply

EN-Product-Metallic coated-All grades Further processingTSUK

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type	Slitting	Decoiling	Blanking
Thickness range (mm)	0.2 - 7.0	0.3 - 6.0	0.3 - 6.0
Width range (mm)	10 - 2050	50 - 2600	200 - 2600
Length range	-	up to 6m	up to 6m
Locations	UK Ireland Netherlands Germany France Spain Sweden Norway Finland	UK Ireland Netherlands Germany France Spain Sweden Norway Finland	UK Netherlands

For further information please visit our service centre webpages.

EN-Product-Metallic coated-Structural steel-DownloadsTSUK

Download

Download:

EN-Engineering-Brochure-MagiZinc

MagiZinc - Brochure

Brochure

English

MagiZinc for superior corrosion protection

tata-steel-engineering-magizinc-corrosion-protection-brochure-en.pdf13.86 MB

EN-Product-Metallic coated-Structural steel-S320GD+Z/+ZM TSUK

S320GD+Z/+ZM

Specification details for S320GD+Z/+ZM

EN-Product-Metallic coated-Structural steel-All Grades OverviewTSUK

Overview

Relationship with standards

Galvanised structural steel complies with the following European standard

EN 10346: 2015
Grade
S220GD+Z/+ZM
S250GD+Z/+ZM
S280GD+Z/+ZM
S320GD+Z/+ZM
S350GD+Z/+ZM
S390GD+Z/+ZM
S420GD+Z/+ZM
S450GD+Z/+ZM
S550GD+Z

For products produced in the Netherlands click here.

EN-Product-Metallic coated-All Grades Coatings Surface aspectsTSUK

Coatings and surface aspects

Coatings

Three types of metallic coating are available:

Pure zinc

Galvanised steel (Z/GI) is coated with an almost pure zinc coating (>99% zinc).

Zinc-iron alloy

Produced in the Netherlands. For further information click here.

MagiZinc

MagiZinc steel (ZM) is coated with a zinc coating containing additional magnesium and aluminium.

Coating weight

Coating	Minimum	Maximum
Pure zinc (Z/GI)	90 (6 µm/side)	275 (20 µm/side)
MagiZinc (ZM)¹	70 (5 µm/side)	310 (22 µm/side)

Coating weight measured in g/m² double-sided (µm, per side).

Surface quality

Surface quality complies with standard: EN 10346:2015. Galvanised steels are available in surface quality A, B or C.
Also, Serica FLO^®surface quality produced in the Netherlands. For further information click here.

Surface quality A: as coated surface

Imperfections such as pimples, marks, scratches, pits, variations in surface appearance, dark spots, stripe marks and light passivation stains are permissible.
Stretch levelling breaks or run-off marks may appear. Coil breaks and stretcher strains may also appear.

Surface quality B: improved surface

With this surface quality, small imperfections such as stretch levelling breaks, skin pass marks, slight scratches, indentations, surface structure, zinc run-off marks and light passivation stains are permissible.

Surface quality C: best quality surface

Surface condition C is obtained by skin passing. The controlled surface for the exposed side enables application of a uniform paint finish. The reverse surface has, at least, the characteristics of surface quality B.

Surface finish

Pure zinc

MA: minimised spangle, as coated surface (Z/GI).
MB: minimised spangle, improved surface (Z/GI).
MC: minimised spangle, best quality surface (Z/GI).

MagiZinc^®

A : as coated surface (ZM).
B : improved surface (ZM).
C: best quality surface (ZM).

Surface roughness

Metallic coated steel (with the exception of galvanised steel with standard surface (MA) can be supplied in various grades of roughness – please contact us for more details. If no roughness is specified, roughness will be as shown in the table below.

Roughness Ra (µm)
cut off 0.8mm	cut off 2.5mm
0.6 - 1.9	0.7 - 2.2

Surface treatments

The surface treatments available are O, C and CO.

Oiling (O)

The material surface can be oiled with preservative oil. Other types of oil - for increasing strength or reducing weight – are available to help achieve your optimum performance parameters. Please contact us for details.

Tata Steel offers the following range of oiling levels:

Coating type	Capability
Pure zinc (Z/GI)	0.5 - 1.6 g/m²
MagiZinc^® (ZM)	0.5 - 1.6 g/m²

Other oiling levels are available on request.

Chromium-free passivation (C)

This surface treatment temporarily protects the zinc-coated material against white rust during transportation and storage (not applicable to all qualities and dimensions – please contact us for details).

Chromium-free passivation and oiled (CO)

Please request this combination of surface treatments if you require extra protection against white rust formation (not applicable to all qualities and dimensions – please contact us for details).

T-treatment

Please contact us for further information.

Prime Lubrication Treatment (PLT)

Prime Lubrication Treatment facilitates the manufacturing of stamped components by minimising known issues in stamping and joining.
Currently Under development, please contact us regarding further information

Untreated (U)

Please contact us regarding the availability of untreated coils.

EN-Product-Metallic Coated-Structural steel-S320GD-Properties TSUK

Properties

Mechanical properties

Metallic coated structural steel grades have the following mechanical properties (skin-passed) - these are measured longitudinal to the rolling direction:

EN 10346: 2015	Grade	S320GD+Z/+ZM
Min. yield strength Rp_0.2	N/mm²	320
Min. tensile strength R_m	N/mm²	390
Elongation	%	17

If the yield point is pronounced, the values apply to the upper yield point R_eH.
A range of 140 N/mm² can be expected for tensile strength.
Elongation after fracture uses test piece length L₀ = 80 mm.
For a thickness t ≤ 0.7 mm the minimum elongation after fracture is decreased by 2% and for a thickness t ≤ 0.5mm the minimum elongation after fracture is decreased by 4%.

Chemical composition

Tata Steel supplies the following cast analysis with maximum values unless otherwise shown:

EN 10346: 2015	Grade	S320GD+Z/+ZM
C	Max.	0.20
Mn	Max.	1.70
P	Max.	0.10
S	Max.	0.045
Si	Max.	0.60

All values in weight%.

EN-Product-Metallic Coated-Structural steel-S320GD-Dimensions TSUK

Dimensions

Dimensional capability

Galvanised (+Z) products

Dimensions in mm.

Thickness	Max. width
From - up to	S320GD
0.45 - 0.65	1360
0.65 - 1.20	1525
1.20 - 1.83	1520
1.83 - 1.91	1465
1.91 - 2.00	1395

For widths below 900 mm, please contact us.
For products produced in the Netherlands click here.

MagiZinc^® (+ZM) products

Dimensions in mm.

Thickness	Max. Width
From - up to	S320GD
0.60 - 0.65	1360
0.65 - 1.20	1525
1.20 - 1.83	1520
1.83 - 1.91	1465
1.91 - 2.00	1395

For widths below 900 mm please contact us.
For products produced in the Netherlands click here.

Tolerances

Tolerances comply with standard EN 10143: 2006.
Tighter tolerances are available - please contact us for details.

EN-Product-Metallic Coated-All Grades Shape and Dimensional TolerancesTSUK

Shape and dimensional tolerances

Tolerances on thickness

The tolerances comply with standard EN 10143: 2006.
Tighter tolerances are available on request.
Thickness tolerance availability is shown below:

Thickness tolerance	Availability
Full thickness tolerance	Available
Special thickness tolerance	Available
50% of full thickness tolerance	Refer before ordering

The following tolerances apply to the grades with a minimum value for the yield strength lower than 260N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
> 0.40	≤ 0.60	± 0.04	± 0.05	± 0.06	± 0.035	± 0.040	± 0.045
> 0.60	≤ 0.80	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.80	≤ 1.00	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 1.00	≤ 1.20	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.20	≤ 1.60	± 0.10	± 0.11	± 0.12	± 0.060	± 0.070	± 0.080
> 1.60	≤ 2.00	± 0.12	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 2.00	≤ 2.50	± 0.14	± 0.15	± 0.16	± 0.090	± 0.100	± 0.110
> 2.50	≤ 3.00	± 0.17	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130
> 3.00	≤ 5.00	± 0.20	± 0.20	± 0.21	± 0.15	± 0.16	± 0.17
> 5.00	≤ 6.50	± 0.22	± 0.22	± 0.23	± 0.17	± 0.18	± 0.19

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 260N/mm^² ≤ R_p0.2 < 360N/mm^² and for grades DX51D and S550GD.

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.035	± 0.040	-
> 0.40	≤ 0.60	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.60	≤ 0.80	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.80	≤ 1.00	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.00	≤ 1.20	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.20	≤ 1.60	± 0.11	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 1.60	≤ 2.00	± 0.14	± 0.15	± 0.16	± 0.080	± 0.090	± 0.110
> 2.00	≤ 2.50	± 0.16	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130
> 2.50	≤ 3.00	± 0.19	± 0.20	± 0.20	± 0.130	± 0.140	± 0.150
> 3.00	≤ 5.00	± 0.22	± 0.24	± 0.25	± 0.17	± 0.18	± 0.19
> 5.00	≤ 6.50	± 0.24	± 0.25	± 0.26	± 0.19	± 0.20	± 0.21

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2.For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm

The following tolerances apply to the steel grades with a minimum value for the yield strength 360N/mm² ≤ R_p0.2 ≤ 420N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.040	± 0.045	-
> 0.40	≤ 0.60	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.60	≤ 0.80	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.80	≤ 1.00	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.00	≤ 1.20	± 0.10	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.20	≤ 1.60	± 0.13	± 0.14	± 0.16	± 0.080	± 0.090	± 0.110
> 1.60	≤ 2.00	± 0.16	± 0.17	± 0.19	± 0.090	± 0.110	± 0.120
> 2.00	≤ 2.50	± 0.18	± 0.20	± 0.21	± 0.120	± 0.130	± 0.140
> 2.50	≤ 3.00	± 0.22	± 0.22	± 0.23	± 0.140	± 0.150	± 0.160
> 3.00	≤ 5.00	± 0.22	± 0.24	± 0.25	± 0.17	± 0.18	± 0.19
> 5.00	≤ 6.50	± 0.24	± 0.25	± 0.26	± 0.19	± 0.20	± 0.21

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 420N/mm² < R_p0.2 ≤ 900N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.06	± 0.07	-	± 0.045	± 0.050	-
> 0.40	≤ 0.60	± 0.06	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.60	≤ 0.80	± 0.07	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 0.80	≤ 1.00	± 0.09	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.00	≤ 1.20	± 0.11	± 0.13	± 0.14	± 0.080	± 0.090	± 0.110
> 1.20	≤ 1.60	± 0.15	± 0.16	± 0.18	± 0.090	± 0.110	± 0.120
> 1.60	≤ 2.00	± 0.18	± 0.19	± 0.21	± 0.110	± 0.120	± 0.140
> 2.00	≤ 2.50	± 0.21	± 0.22	± 0.24	± 0.140	± 0.150	± 0.170
> 2.50	≤ 3.00	± 0.24	± 0.25	± 0.26	± 0.170	± 0.180	± 0.190
> 3.00	≤ 5.00	± 0.26	± 0.27	± 0.28	± 0.23	± 0.24	± 0.26
> 5.00	≤ 6.50	± 0.28	± 0.29	± 0.30	± 0.25	± 0.26	± 0.28

_{^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed}
_{over a length of 15 metres.}
_{^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.}

Tolerances on width

The tolerances on width comply with standard EN 10143: 2006
MagiZinc is not included in the standard, but fulfils EN 10143: 2006 requirements.
Tighter tolerances are available on request.

Tolerances in mm.

Nominal width w	Normal tolerances	Special tolerances (S)
600 ≤ w ≤ 1200	+ 5 0	+ 2 0
1200 < w ≤ 1500	+ 6 0	+ 2 0
1500 < w ≤ 1800	+ 7 0	+ 3 0
w > 1800	+ 8 0	+ 3 0

Dimensions and coil weights

Description	Availability
Coil diameter inner	610mm
Coil diameter inner	(508 mm available on request)
Coil diameter outer	10/7 x width max
	1000mm min.
	2500mm max.
Coil weight	30t max.
	Coil weight limited by maximum outer diameter
	Maximum weight allowed by road/rail transport
	Some products may have different coil weight ranges available
	Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
Minimum tonnage per order	Refer to price list for order quantity details
Minimum tonnage per order	Minimum order quantities may apply

EN-Product-Metallic coated-All grades Further processingTSUK

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type	Slitting	Decoiling	Blanking
Thickness range (mm)	0.2 - 7.0	0.3 - 6.0	0.3 - 6.0
Width range (mm)	10 - 2050	50 - 2600	200 - 2600
Length range	-	up to 6m	up to 6m
Locations	UK Ireland Netherlands Germany France Spain Sweden Norway Finland	UK Ireland Netherlands Germany France Spain Sweden Norway Finland	UK Netherlands

For further information please visit our service centre webpages.

EN-Product-Metallic coated-Structural steel-DownloadsTSUK

Download

Download:

EN-Engineering-Brochure-MagiZinc

MagiZinc - Brochure

Brochure

English

MagiZinc for superior corrosion protection

tata-steel-engineering-magizinc-corrosion-protection-brochure-en.pdf13.86 MB

EN-Product-Metallic coated-Structural steel-S350GD+Z/+ZM TSUK

S350GD+Z/+ZM

Specification details for S350GD+Z/+ZM

EN-Product-Metallic coated-Structural steel-All Grades OverviewTSUK

Overview

Relationship with standards

Galvanised structural steel complies with the following European standard

EN 10346: 2015
Grade
S220GD+Z/+ZM
S250GD+Z/+ZM
S280GD+Z/+ZM
S320GD+Z/+ZM
S350GD+Z/+ZM
S390GD+Z/+ZM
S420GD+Z/+ZM
S450GD+Z/+ZM
S550GD+Z

For products produced in the Netherlands click here.

EN-Product-Metallic coated-All Grades Coatings Surface aspectsTSUK

Coatings and surface aspects

Coatings

Three types of metallic coating are available:

Pure zinc

Galvanised steel (Z/GI) is coated with an almost pure zinc coating (>99% zinc).

Zinc-iron alloy

Produced in the Netherlands. For further information click here.

MagiZinc

MagiZinc steel (ZM) is coated with a zinc coating containing additional magnesium and aluminium.

Coating weight

Coating	Minimum	Maximum
Pure zinc (Z/GI)	90 (6 µm/side)	275 (20 µm/side)
MagiZinc (ZM)¹	70 (5 µm/side)	310 (22 µm/side)

Coating weight measured in g/m² double-sided (µm, per side).

Surface quality

Surface quality complies with standard: EN 10346:2015. Galvanised steels are available in surface quality A, B or C.
Also, Serica FLO^®surface quality produced in the Netherlands. For further information click here.

Surface quality A: as coated surface

Imperfections such as pimples, marks, scratches, pits, variations in surface appearance, dark spots, stripe marks and light passivation stains are permissible.
Stretch levelling breaks or run-off marks may appear. Coil breaks and stretcher strains may also appear.

Surface quality B: improved surface

With this surface quality, small imperfections such as stretch levelling breaks, skin pass marks, slight scratches, indentations, surface structure, zinc run-off marks and light passivation stains are permissible.

Surface quality C: best quality surface

Surface condition C is obtained by skin passing. The controlled surface for the exposed side enables application of a uniform paint finish. The reverse surface has, at least, the characteristics of surface quality B.

Surface finish

Pure zinc

MA: minimised spangle, as coated surface (Z/GI).
MB: minimised spangle, improved surface (Z/GI).
MC: minimised spangle, best quality surface (Z/GI).

MagiZinc^®

A : as coated surface (ZM).
B : improved surface (ZM).
C: best quality surface (ZM).

Surface roughness

Metallic coated steel (with the exception of galvanised steel with standard surface (MA) can be supplied in various grades of roughness – please contact us for more details. If no roughness is specified, roughness will be as shown in the table below.

Roughness Ra (µm)
cut off 0.8mm	cut off 2.5mm
0.6 - 1.9	0.7 - 2.2

Surface treatments

The surface treatments available are O, C and CO.

Oiling (O)

The material surface can be oiled with preservative oil. Other types of oil - for increasing strength or reducing weight – are available to help achieve your optimum performance parameters. Please contact us for details.

Tata Steel offers the following range of oiling levels:

Coating type	Capability
Pure zinc (Z/GI)	0.5 - 1.6 g/m²
MagiZinc^® (ZM)	0.5 - 1.6 g/m²

Other oiling levels are available on request.

Chromium-free passivation (C)

This surface treatment temporarily protects the zinc-coated material against white rust during transportation and storage (not applicable to all qualities and dimensions – please contact us for details).

Chromium-free passivation and oiled (CO)

Please request this combination of surface treatments if you require extra protection against white rust formation (not applicable to all qualities and dimensions – please contact us for details).

T-treatment

Please contact us for further information.

Prime Lubrication Treatment (PLT)

Prime Lubrication Treatment facilitates the manufacturing of stamped components by minimising known issues in stamping and joining.
Currently Under development, please contact us regarding further information

Untreated (U)

Please contact us regarding the availability of untreated coils.

EN-Product-Metallic Coated-Structural steel-S350GD-Properties TSUK

Properties

Mechanical properties

Metallic coated structural steel grades have the following mechanical properties (skin-passed) - these are measured longitudinal to the rolling direction:

EN 10346: 2015	Grade	S350GD+Z/+ZM
Min. yield strength Rp_0.2	N/mm²	350
Min. tensile strength R_m	N/mm²	420
Elongation	%	16

If the yield point is pronounced, the values apply to the upper yield point R_eH.
A range of 140 N/mm² can be expected for tensile strength.
Elongation after fracture uses test piece length L₀ = 80 mm.
For a thickness t ≤ 0.7 mm the minimum elongation after fracture is decreased by 2% and for a thickness t ≤ 0.5mm the minimum elongation after fracture is decreased by 4%.

Chemical composition

Tata Steel supplies the following cast analysis with maximum values unless otherwise shown:

EN 10346: 2015	Grade	S350GD+Z/+ZM
C	Max.	0.20
Si	Max.	0.60
Mn	Max.	1.70
P	Max.	0.10
S	Max.	0.045
Si	Max.	0.60

All values in weight%.

EN-Product-Metallic Coated-Structural steel-S350GD-Dimensions TSUK

Dimensions

Dimensional capability

Galvanised (+Z) products

Dimensions in mm.

Thickness	Max. width
From - up to	S350GD
0.45 - 0.65	1360
0.65 - 1.20	1525
1.20 - 1.83	1520
1.83 - 1.91	1465
1.91 - 2.00	1395

For widths below 900 mm, please contact us.
For products produced in the Netherlands click here.

MagiZinc^® (+ZM) products

Dimensions in mm.

Thickness	Max. width
From - up to	S350GD
0.45 - 0.65	1360
0.65 - 1.20	1525
1.20 - 1.83	1520
1.83 - 1.91	1465
1.91 - 2.00	1395

For widths below 900 mm, please contact us.
For products produced in the Netherlands click here.

Tolerances

Tolerances comply with standard EN 10143: 2006.
Tighter tolerances are available - please contact us for details.

EN-Product-Metallic Coated-All Grades Shape and Dimensional TolerancesTSUK

Shape and dimensional tolerances

Tolerances on thickness

The tolerances comply with standard EN 10143: 2006.
Tighter tolerances are available on request.
Thickness tolerance availability is shown below:

Thickness tolerance	Availability
Full thickness tolerance	Available
Special thickness tolerance	Available
50% of full thickness tolerance	Refer before ordering

The following tolerances apply to the grades with a minimum value for the yield strength lower than 260N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
> 0.40	≤ 0.60	± 0.04	± 0.05	± 0.06	± 0.035	± 0.040	± 0.045
> 0.60	≤ 0.80	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.80	≤ 1.00	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 1.00	≤ 1.20	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.20	≤ 1.60	± 0.10	± 0.11	± 0.12	± 0.060	± 0.070	± 0.080
> 1.60	≤ 2.00	± 0.12	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 2.00	≤ 2.50	± 0.14	± 0.15	± 0.16	± 0.090	± 0.100	± 0.110
> 2.50	≤ 3.00	± 0.17	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130
> 3.00	≤ 5.00	± 0.20	± 0.20	± 0.21	± 0.15	± 0.16	± 0.17
> 5.00	≤ 6.50	± 0.22	± 0.22	± 0.23	± 0.17	± 0.18	± 0.19

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 260N/mm^² ≤ R_p0.2 < 360N/mm^² and for grades DX51D and S550GD.

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.035	± 0.040	-
> 0.40	≤ 0.60	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.60	≤ 0.80	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.80	≤ 1.00	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.00	≤ 1.20	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.20	≤ 1.60	± 0.11	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 1.60	≤ 2.00	± 0.14	± 0.15	± 0.16	± 0.080	± 0.090	± 0.110
> 2.00	≤ 2.50	± 0.16	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130
> 2.50	≤ 3.00	± 0.19	± 0.20	± 0.20	± 0.130	± 0.140	± 0.150
> 3.00	≤ 5.00	± 0.22	± 0.24	± 0.25	± 0.17	± 0.18	± 0.19
> 5.00	≤ 6.50	± 0.24	± 0.25	± 0.26	± 0.19	± 0.20	± 0.21

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2.For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm

The following tolerances apply to the steel grades with a minimum value for the yield strength 360N/mm² ≤ R_p0.2 ≤ 420N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.040	± 0.045	-
> 0.40	≤ 0.60	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.60	≤ 0.80	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.80	≤ 1.00	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.00	≤ 1.20	± 0.10	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.20	≤ 1.60	± 0.13	± 0.14	± 0.16	± 0.080	± 0.090	± 0.110
> 1.60	≤ 2.00	± 0.16	± 0.17	± 0.19	± 0.090	± 0.110	± 0.120
> 2.00	≤ 2.50	± 0.18	± 0.20	± 0.21	± 0.120	± 0.130	± 0.140
> 2.50	≤ 3.00	± 0.22	± 0.22	± 0.23	± 0.140	± 0.150	± 0.160
> 3.00	≤ 5.00	± 0.22	± 0.24	± 0.25	± 0.17	± 0.18	± 0.19
> 5.00	≤ 6.50	± 0.24	± 0.25	± 0.26	± 0.19	± 0.20	± 0.21

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 420N/mm² < R_p0.2 ≤ 900N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.06	± 0.07	-	± 0.045	± 0.050	-
> 0.40	≤ 0.60	± 0.06	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.60	≤ 0.80	± 0.07	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 0.80	≤ 1.00	± 0.09	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.00	≤ 1.20	± 0.11	± 0.13	± 0.14	± 0.080	± 0.090	± 0.110
> 1.20	≤ 1.60	± 0.15	± 0.16	± 0.18	± 0.090	± 0.110	± 0.120
> 1.60	≤ 2.00	± 0.18	± 0.19	± 0.21	± 0.110	± 0.120	± 0.140
> 2.00	≤ 2.50	± 0.21	± 0.22	± 0.24	± 0.140	± 0.150	± 0.170
> 2.50	≤ 3.00	± 0.24	± 0.25	± 0.26	± 0.170	± 0.180	± 0.190
> 3.00	≤ 5.00	± 0.26	± 0.27	± 0.28	± 0.23	± 0.24	± 0.26
> 5.00	≤ 6.50	± 0.28	± 0.29	± 0.30	± 0.25	± 0.26	± 0.28

_{^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed}
_{over a length of 15 metres.}
_{^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.}

Tolerances on width

The tolerances on width comply with standard EN 10143: 2006
MagiZinc is not included in the standard, but fulfils EN 10143: 2006 requirements.
Tighter tolerances are available on request.

Tolerances in mm.

Nominal width w	Normal tolerances	Special tolerances (S)
600 ≤ w ≤ 1200	+ 5 0	+ 2 0
1200 < w ≤ 1500	+ 6 0	+ 2 0
1500 < w ≤ 1800	+ 7 0	+ 3 0
w > 1800	+ 8 0	+ 3 0

Dimensions and coil weights

Description	Availability
Coil diameter inner	610mm
Coil diameter inner	(508 mm available on request)
Coil diameter outer	10/7 x width max
	1000mm min.
	2500mm max.
Coil weight	30t max.
	Coil weight limited by maximum outer diameter
	Maximum weight allowed by road/rail transport
	Some products may have different coil weight ranges available
	Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
Minimum tonnage per order	Refer to price list for order quantity details
Minimum tonnage per order	Minimum order quantities may apply

EN-Product-Metallic coated-All grades Further processingTSUK

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type	Slitting	Decoiling	Blanking
Thickness range (mm)	0.2 - 7.0	0.3 - 6.0	0.3 - 6.0
Width range (mm)	10 - 2050	50 - 2600	200 - 2600
Length range	-	up to 6m	up to 6m
Locations	UK Ireland Netherlands Germany France Spain Sweden Norway Finland	UK Ireland Netherlands Germany France Spain Sweden Norway Finland	UK Netherlands

For further information please visit our service centre webpages.

EN-Product-Metallic coated-Structural steel-DownloadsTSUK

Download

Download:

EN-Engineering-Brochure-MagiZinc

MagiZinc - Brochure

Brochure

English

MagiZinc for superior corrosion protection

tata-steel-engineering-magizinc-corrosion-protection-brochure-en.pdf13.86 MB

EN-Product-Metallic coated-Structural steel-S390GD+Z/+ZM TSUK

S390GD+Z/+ZM

Specification details for S390GD+Z/+ZM

EN-Product-Metallic coated-Structural steel-All Grades OverviewTSUK

Overview

Relationship with standards

Galvanised structural steel complies with the following European standard

EN 10346: 2015
Grade
S220GD+Z/+ZM
S250GD+Z/+ZM
S280GD+Z/+ZM
S320GD+Z/+ZM
S350GD+Z/+ZM
S390GD+Z/+ZM
S420GD+Z/+ZM
S450GD+Z/+ZM
S550GD+Z

For products produced in the Netherlands click here.

EN-Product-Metallic coated-All Grades Coatings Surface aspectsTSUK

Coatings and surface aspects

Coatings

Three types of metallic coating are available:

Pure zinc

Galvanised steel (Z/GI) is coated with an almost pure zinc coating (>99% zinc).

Zinc-iron alloy

Produced in the Netherlands. For further information click here.

MagiZinc

MagiZinc steel (ZM) is coated with a zinc coating containing additional magnesium and aluminium.

Coating weight

Coating	Minimum	Maximum
Pure zinc (Z/GI)	90 (6 µm/side)	275 (20 µm/side)
MagiZinc (ZM)¹	70 (5 µm/side)	310 (22 µm/side)

Coating weight measured in g/m² double-sided (µm, per side).

Surface quality

Surface quality complies with standard: EN 10346:2015. Galvanised steels are available in surface quality A, B or C.
Also, Serica FLO^®surface quality produced in the Netherlands. For further information click here.

Surface quality A: as coated surface

Imperfections such as pimples, marks, scratches, pits, variations in surface appearance, dark spots, stripe marks and light passivation stains are permissible.
Stretch levelling breaks or run-off marks may appear. Coil breaks and stretcher strains may also appear.

Surface quality B: improved surface

With this surface quality, small imperfections such as stretch levelling breaks, skin pass marks, slight scratches, indentations, surface structure, zinc run-off marks and light passivation stains are permissible.

Surface quality C: best quality surface

Surface condition C is obtained by skin passing. The controlled surface for the exposed side enables application of a uniform paint finish. The reverse surface has, at least, the characteristics of surface quality B.

Surface finish

Pure zinc

MA: minimised spangle, as coated surface (Z/GI).
MB: minimised spangle, improved surface (Z/GI).
MC: minimised spangle, best quality surface (Z/GI).

MagiZinc^®

A : as coated surface (ZM).
B : improved surface (ZM).
C: best quality surface (ZM).

Surface roughness

Metallic coated steel (with the exception of galvanised steel with standard surface (MA) can be supplied in various grades of roughness – please contact us for more details. If no roughness is specified, roughness will be as shown in the table below.

Roughness Ra (µm)
cut off 0.8mm	cut off 2.5mm
0.6 - 1.9	0.7 - 2.2

Surface treatments

The surface treatments available are O, C and CO.

Oiling (O)

The material surface can be oiled with preservative oil. Other types of oil - for increasing strength or reducing weight – are available to help achieve your optimum performance parameters. Please contact us for details.

Tata Steel offers the following range of oiling levels:

Coating type	Capability
Pure zinc (Z/GI)	0.5 - 1.6 g/m²
MagiZinc^® (ZM)	0.5 - 1.6 g/m²

Other oiling levels are available on request.

Chromium-free passivation (C)

This surface treatment temporarily protects the zinc-coated material against white rust during transportation and storage (not applicable to all qualities and dimensions – please contact us for details).

Chromium-free passivation and oiled (CO)

Please request this combination of surface treatments if you require extra protection against white rust formation (not applicable to all qualities and dimensions – please contact us for details).

T-treatment

Please contact us for further information.

Prime Lubrication Treatment (PLT)

Prime Lubrication Treatment facilitates the manufacturing of stamped components by minimising known issues in stamping and joining.
Currently Under development, please contact us regarding further information

Untreated (U)

Please contact us regarding the availability of untreated coils.

EN-Product-Metallic Coated-Structural steel-S390GD-Properties TSUK

Properties

Mechanical properties

Metallic coated structural steel grades have the following mechanical properties (skin-passed) - these are measured longitudinal to the rolling direction:

EN 10346: 2015	Grade	S390GD+Z/+ZM
Min. yield strength Rp_0.2	N/mm²	390
Min. tensile strength R_m	N/mm²	460
Elongation	%	16

If the yield point is pronounced, the values apply to the upper yield point R_eH.
A range of 140 N/mm² can be expected for tensile strength.
Elongation after fracture uses test piece length L₀ = 80 mm.
For a thickness t ≤ 0.7 mm the minimum elongation after fracture is decreased by 2% and for a thickness t ≤ 0.5mm the minimum elongation after fracture is decreased by 4%.

Chemical composition

Tata Steel supplies the following cast analysis with maximum values unless otherwise shown:

EN 10346: 2015	Grade	S390GD+Z/+ZM
C	Max.	0.20
Mn	Max.	1.70
P	Max.	0.10
S	Max.	0.045
Si	Max.	0.60

All values in weight%.

EN-Product-Metallic Coated-Structural steel-S390GD-Dimensions TSUK

Dimensions

Dimensional capability

Galvanised (+Z) products

Dimensions in mm.

Thickness	Max. width
From - up to	S350GD
0.45 - 0.65	1360
0.65 - 1.20	1525
1.20 - 1.83	1520
1.83 - 1.91	1465
1.91 - 2.00	1395

For widths below 900 mm, please contact us.
For products produced in the Netherlands click here.

MagiZinc^® (+ZM) products

Dimensions in mm.

Thickness	Max. width
From - up to	S350GD
0.60 - 0.65	1360
0.65 - 1.20	1525
1.20 - 1.83	1520
1.83 - 1.91	1465
1.91 - 2.00	1395

For widths below 900 mm please contact us.
For products produced in the Netherlands click here.

Tolerances

Tolerances comply with standard EN 10143: 2006.
Tighter tolerances are available - please contact us for details.

EN-Product-Metallic Coated-All Grades Shape and Dimensional TolerancesTSUK

Shape and dimensional tolerances

Tolerances on thickness

The tolerances comply with standard EN 10143: 2006.
Tighter tolerances are available on request.
Thickness tolerance availability is shown below:

Thickness tolerance	Availability
Full thickness tolerance	Available
Special thickness tolerance	Available
50% of full thickness tolerance	Refer before ordering

The following tolerances apply to the grades with a minimum value for the yield strength lower than 260N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
> 0.40	≤ 0.60	± 0.04	± 0.05	± 0.06	± 0.035	± 0.040	± 0.045
> 0.60	≤ 0.80	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.80	≤ 1.00	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 1.00	≤ 1.20	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.20	≤ 1.60	± 0.10	± 0.11	± 0.12	± 0.060	± 0.070	± 0.080
> 1.60	≤ 2.00	± 0.12	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 2.00	≤ 2.50	± 0.14	± 0.15	± 0.16	± 0.090	± 0.100	± 0.110
> 2.50	≤ 3.00	± 0.17	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130
> 3.00	≤ 5.00	± 0.20	± 0.20	± 0.21	± 0.15	± 0.16	± 0.17
> 5.00	≤ 6.50	± 0.22	± 0.22	± 0.23	± 0.17	± 0.18	± 0.19

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 260N/mm^² ≤ R_p0.2 < 360N/mm^² and for grades DX51D and S550GD.

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.035	± 0.040	-
> 0.40	≤ 0.60	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.60	≤ 0.80	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.80	≤ 1.00	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.00	≤ 1.20	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.20	≤ 1.60	± 0.11	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 1.60	≤ 2.00	± 0.14	± 0.15	± 0.16	± 0.080	± 0.090	± 0.110
> 2.00	≤ 2.50	± 0.16	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130
> 2.50	≤ 3.00	± 0.19	± 0.20	± 0.20	± 0.130	± 0.140	± 0.150
> 3.00	≤ 5.00	± 0.22	± 0.24	± 0.25	± 0.17	± 0.18	± 0.19
> 5.00	≤ 6.50	± 0.24	± 0.25	± 0.26	± 0.19	± 0.20	± 0.21

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2.For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm

The following tolerances apply to the steel grades with a minimum value for the yield strength 360N/mm² ≤ R_p0.2 ≤ 420N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.040	± 0.045	-
> 0.40	≤ 0.60	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.60	≤ 0.80	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.80	≤ 1.00	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.00	≤ 1.20	± 0.10	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.20	≤ 1.60	± 0.13	± 0.14	± 0.16	± 0.080	± 0.090	± 0.110
> 1.60	≤ 2.00	± 0.16	± 0.17	± 0.19	± 0.090	± 0.110	± 0.120
> 2.00	≤ 2.50	± 0.18	± 0.20	± 0.21	± 0.120	± 0.130	± 0.140
> 2.50	≤ 3.00	± 0.22	± 0.22	± 0.23	± 0.140	± 0.150	± 0.160
> 3.00	≤ 5.00	± 0.22	± 0.24	± 0.25	± 0.17	± 0.18	± 0.19
> 5.00	≤ 6.50	± 0.24	± 0.25	± 0.26	± 0.19	± 0.20	± 0.21

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 420N/mm² < R_p0.2 ≤ 900N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.06	± 0.07	-	± 0.045	± 0.050	-
> 0.40	≤ 0.60	± 0.06	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.60	≤ 0.80	± 0.07	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 0.80	≤ 1.00	± 0.09	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.00	≤ 1.20	± 0.11	± 0.13	± 0.14	± 0.080	± 0.090	± 0.110
> 1.20	≤ 1.60	± 0.15	± 0.16	± 0.18	± 0.090	± 0.110	± 0.120
> 1.60	≤ 2.00	± 0.18	± 0.19	± 0.21	± 0.110	± 0.120	± 0.140
> 2.00	≤ 2.50	± 0.21	± 0.22	± 0.24	± 0.140	± 0.150	± 0.170
> 2.50	≤ 3.00	± 0.24	± 0.25	± 0.26	± 0.170	± 0.180	± 0.190
> 3.00	≤ 5.00	± 0.26	± 0.27	± 0.28	± 0.23	± 0.24	± 0.26
> 5.00	≤ 6.50	± 0.28	± 0.29	± 0.30	± 0.25	± 0.26	± 0.28

_{^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed}
_{over a length of 15 metres.}
_{^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.}

Tolerances on width

The tolerances on width comply with standard EN 10143: 2006
MagiZinc is not included in the standard, but fulfils EN 10143: 2006 requirements.
Tighter tolerances are available on request.

Tolerances in mm.

Nominal width w	Normal tolerances	Special tolerances (S)
600 ≤ w ≤ 1200	+ 5 0	+ 2 0
1200 < w ≤ 1500	+ 6 0	+ 2 0
1500 < w ≤ 1800	+ 7 0	+ 3 0
w > 1800	+ 8 0	+ 3 0

Dimensions and coil weights

Description	Availability
Coil diameter inner	610mm
Coil diameter inner	(508 mm available on request)
Coil diameter outer	10/7 x width max
	1000mm min.
	2500mm max.
Coil weight	30t max.
	Coil weight limited by maximum outer diameter
	Maximum weight allowed by road/rail transport
	Some products may have different coil weight ranges available
	Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
Minimum tonnage per order	Refer to price list for order quantity details
Minimum tonnage per order	Minimum order quantities may apply

EN-Product-Metallic coated-All grades Further processingTSUK

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type	Slitting	Decoiling	Blanking
Thickness range (mm)	0.2 - 7.0	0.3 - 6.0	0.3 - 6.0
Width range (mm)	10 - 2050	50 - 2600	200 - 2600
Length range	-	up to 6m	up to 6m
Locations	UK Ireland Netherlands Germany France Spain Sweden Norway Finland	UK Ireland Netherlands Germany France Spain Sweden Norway Finland	UK Netherlands

For further information please visit our service centre webpages.

EN-Product-Metallic coated-Structural steel-DownloadsTSUK

Download

Download:

EN-Engineering-Brochure-MagiZinc

MagiZinc - Brochure

Brochure

English

MagiZinc for superior corrosion protection

tata-steel-engineering-magizinc-corrosion-protection-brochure-en.pdf13.86 MB

EN-Product-Metallic coated-Structural steel-S420GD+Z/+ZM TSUK

S420GD+Z/+ZM

Specification details for S420GD+Z/+ZM

EN-Product-Metallic coated-Structural steel-All Grades OverviewTSUK

Overview

Relationship with standards

Galvanised structural steel complies with the following European standard

EN 10346: 2015
Grade
S220GD+Z/+ZM
S250GD+Z/+ZM
S280GD+Z/+ZM
S320GD+Z/+ZM
S350GD+Z/+ZM
S390GD+Z/+ZM
S420GD+Z/+ZM
S450GD+Z/+ZM
S550GD+Z

For products produced in the Netherlands click here.

EN-Product-Metallic coated-All Grades Coatings Surface aspectsTSUK

Coatings and surface aspects

Coatings

Three types of metallic coating are available:

Pure zinc

Galvanised steel (Z/GI) is coated with an almost pure zinc coating (>99% zinc).

Zinc-iron alloy

Produced in the Netherlands. For further information click here.

MagiZinc

MagiZinc steel (ZM) is coated with a zinc coating containing additional magnesium and aluminium.

Coating weight

Coating	Minimum	Maximum
Pure zinc (Z/GI)	90 (6 µm/side)	275 (20 µm/side)
MagiZinc (ZM)¹	70 (5 µm/side)	310 (22 µm/side)

Coating weight measured in g/m² double-sided (µm, per side).

Surface quality

Surface quality complies with standard: EN 10346:2015. Galvanised steels are available in surface quality A, B or C.
Also, Serica FLO^®surface quality produced in the Netherlands. For further information click here.

Surface quality A: as coated surface

Imperfections such as pimples, marks, scratches, pits, variations in surface appearance, dark spots, stripe marks and light passivation stains are permissible.
Stretch levelling breaks or run-off marks may appear. Coil breaks and stretcher strains may also appear.

Surface quality B: improved surface

With this surface quality, small imperfections such as stretch levelling breaks, skin pass marks, slight scratches, indentations, surface structure, zinc run-off marks and light passivation stains are permissible.

Surface quality C: best quality surface

Surface condition C is obtained by skin passing. The controlled surface for the exposed side enables application of a uniform paint finish. The reverse surface has, at least, the characteristics of surface quality B.

Surface finish

Pure zinc

MA: minimised spangle, as coated surface (Z/GI).
MB: minimised spangle, improved surface (Z/GI).
MC: minimised spangle, best quality surface (Z/GI).

MagiZinc^®

A : as coated surface (ZM).
B : improved surface (ZM).
C: best quality surface (ZM).

Surface roughness

Metallic coated steel (with the exception of galvanised steel with standard surface (MA) can be supplied in various grades of roughness – please contact us for more details. If no roughness is specified, roughness will be as shown in the table below.

Roughness Ra (µm)
cut off 0.8mm	cut off 2.5mm
0.6 - 1.9	0.7 - 2.2

Surface treatments

The surface treatments available are O, C and CO.

Oiling (O)

The material surface can be oiled with preservative oil. Other types of oil - for increasing strength or reducing weight – are available to help achieve your optimum performance parameters. Please contact us for details.

Tata Steel offers the following range of oiling levels:

Coating type	Capability
Pure zinc (Z/GI)	0.5 - 1.6 g/m²
MagiZinc^® (ZM)	0.5 - 1.6 g/m²

Other oiling levels are available on request.

Chromium-free passivation (C)

This surface treatment temporarily protects the zinc-coated material against white rust during transportation and storage (not applicable to all qualities and dimensions – please contact us for details).

Chromium-free passivation and oiled (CO)

Please request this combination of surface treatments if you require extra protection against white rust formation (not applicable to all qualities and dimensions – please contact us for details).

T-treatment

Please contact us for further information.

Prime Lubrication Treatment (PLT)

Prime Lubrication Treatment facilitates the manufacturing of stamped components by minimising known issues in stamping and joining.
Currently Under development, please contact us regarding further information

Untreated (U)

Please contact us regarding the availability of untreated coils.

EN-Product-Metallic Coated-Structural steel-S420GD-Properties TSUK

Properties

Mechanical properties

Metallic coated structural steel grades have the following mechanical properties (skin-passed) - these are measured longitudinal to the rolling direction:

EN 10346: 2015	Grade	S420GD+Z/+ZM
Min. yield strength Rp_0.2	N/mm²	420
Min. tensile strength R_m	N/mm²	480
Elongation	%	15

If the yield point is pronounced, the values apply to the upper yield point R_eH.
A range of 140 N/mm² can be expected for tensile strength.
Elongation after fracture uses test piece length L₀ = 80 mm.
For a thickness t ≤ 0.7 mm the minimum elongation after fracture is decreased by 2% and for a thickness t ≤ 0.5mm the minimum elongation after fracture is decreased by 4%.

Chemical composition

Tata Steel supplies the following cast analysis with maximum values unless otherwise shown:

EN 10346: 2015	Grade	S420GD+Z/+ZM
C	Max.	0.20
Mn	Max.	1.70
P	Max.	0.10
S	Max.	0.045
Si	Max.	0.60

All values in weight%.

EN-Product-Metallic Coated-Structural steel-S420GD-Dimensions TSUK

Dimensions

Dimensional capability

Galvanised (+Z) products

Dimensions in mm.

Thickness	Max. width
From - up to	S420GD
0.70 - 1.00	1250
1.00 - 1.20	1300
1.20 - 1.40	1330
1.40 - 1.70	1360
1.70 - 2.00	1399

For widths below 900 mm, please contact us.
For products produced in the Netherlands click here.

MagiZinc^® (+ZM) products

Dimensions in mm.

Thickness	Max. width
From - up to	S420GD
0.70 - 0.80	1299
0.80 - 0.90	1349
0.90 - 2.00	1399

For widths below 1100 mm please contact us.
For products produced in the Netherlands click here.

Tolerances

Tolerances comply with standard EN 10143: 2006.
Tighter tolerances are available - please contact us for details.

EN-Product-Metallic Coated-All Grades Shape and Dimensional TolerancesTSUK

Shape and dimensional tolerances

Tolerances on thickness

The tolerances comply with standard EN 10143: 2006.
Tighter tolerances are available on request.
Thickness tolerance availability is shown below:

Thickness tolerance	Availability
Full thickness tolerance	Available
Special thickness tolerance	Available
50% of full thickness tolerance	Refer before ordering

The following tolerances apply to the grades with a minimum value for the yield strength lower than 260N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
> 0.40	≤ 0.60	± 0.04	± 0.05	± 0.06	± 0.035	± 0.040	± 0.045
> 0.60	≤ 0.80	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.80	≤ 1.00	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 1.00	≤ 1.20	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.20	≤ 1.60	± 0.10	± 0.11	± 0.12	± 0.060	± 0.070	± 0.080
> 1.60	≤ 2.00	± 0.12	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 2.00	≤ 2.50	± 0.14	± 0.15	± 0.16	± 0.090	± 0.100	± 0.110
> 2.50	≤ 3.00	± 0.17	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130
> 3.00	≤ 5.00	± 0.20	± 0.20	± 0.21	± 0.15	± 0.16	± 0.17
> 5.00	≤ 6.50	± 0.22	± 0.22	± 0.23	± 0.17	± 0.18	± 0.19

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 260N/mm^² ≤ R_p0.2 < 360N/mm^² and for grades DX51D and S550GD.

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.035	± 0.040	-
> 0.40	≤ 0.60	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.60	≤ 0.80	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.80	≤ 1.00	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.00	≤ 1.20	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.20	≤ 1.60	± 0.11	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 1.60	≤ 2.00	± 0.14	± 0.15	± 0.16	± 0.080	± 0.090	± 0.110
> 2.00	≤ 2.50	± 0.16	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130
> 2.50	≤ 3.00	± 0.19	± 0.20	± 0.20	± 0.130	± 0.140	± 0.150
> 3.00	≤ 5.00	± 0.22	± 0.24	± 0.25	± 0.17	± 0.18	± 0.19
> 5.00	≤ 6.50	± 0.24	± 0.25	± 0.26	± 0.19	± 0.20	± 0.21

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2.For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm

The following tolerances apply to the steel grades with a minimum value for the yield strength 360N/mm² ≤ R_p0.2 ≤ 420N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.040	± 0.045	-
> 0.40	≤ 0.60	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.60	≤ 0.80	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.80	≤ 1.00	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.00	≤ 1.20	± 0.10	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.20	≤ 1.60	± 0.13	± 0.14	± 0.16	± 0.080	± 0.090	± 0.110
> 1.60	≤ 2.00	± 0.16	± 0.17	± 0.19	± 0.090	± 0.110	± 0.120
> 2.00	≤ 2.50	± 0.18	± 0.20	± 0.21	± 0.120	± 0.130	± 0.140
> 2.50	≤ 3.00	± 0.22	± 0.22	± 0.23	± 0.140	± 0.150	± 0.160
> 3.00	≤ 5.00	± 0.22	± 0.24	± 0.25	± 0.17	± 0.18	± 0.19
> 5.00	≤ 6.50	± 0.24	± 0.25	± 0.26	± 0.19	± 0.20	± 0.21

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 420N/mm² < R_p0.2 ≤ 900N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.06	± 0.07	-	± 0.045	± 0.050	-
> 0.40	≤ 0.60	± 0.06	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.60	≤ 0.80	± 0.07	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 0.80	≤ 1.00	± 0.09	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.00	≤ 1.20	± 0.11	± 0.13	± 0.14	± 0.080	± 0.090	± 0.110
> 1.20	≤ 1.60	± 0.15	± 0.16	± 0.18	± 0.090	± 0.110	± 0.120
> 1.60	≤ 2.00	± 0.18	± 0.19	± 0.21	± 0.110	± 0.120	± 0.140
> 2.00	≤ 2.50	± 0.21	± 0.22	± 0.24	± 0.140	± 0.150	± 0.170
> 2.50	≤ 3.00	± 0.24	± 0.25	± 0.26	± 0.170	± 0.180	± 0.190
> 3.00	≤ 5.00	± 0.26	± 0.27	± 0.28	± 0.23	± 0.24	± 0.26
> 5.00	≤ 6.50	± 0.28	± 0.29	± 0.30	± 0.25	± 0.26	± 0.28

_{^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed}
_{over a length of 15 metres.}
_{^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.}

Tolerances on width

The tolerances on width comply with standard EN 10143: 2006
MagiZinc is not included in the standard, but fulfils EN 10143: 2006 requirements.
Tighter tolerances are available on request.

Tolerances in mm.

Nominal width w	Normal tolerances	Special tolerances (S)
600 ≤ w ≤ 1200	+ 5 0	+ 2 0
1200 < w ≤ 1500	+ 6 0	+ 2 0
1500 < w ≤ 1800	+ 7 0	+ 3 0
w > 1800	+ 8 0	+ 3 0

Dimensions and coil weights

Description	Availability
Coil diameter inner	610mm
Coil diameter inner	(508 mm available on request)
Coil diameter outer	10/7 x width max
	1000mm min.
	2500mm max.
Coil weight	30t max.
	Coil weight limited by maximum outer diameter
	Maximum weight allowed by road/rail transport
	Some products may have different coil weight ranges available
	Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
Minimum tonnage per order	Refer to price list for order quantity details
Minimum tonnage per order	Minimum order quantities may apply

EN-Product-Metallic coated-All grades Further processingTSUK

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type	Slitting	Decoiling	Blanking
Thickness range (mm)	0.2 - 7.0	0.3 - 6.0	0.3 - 6.0
Width range (mm)	10 - 2050	50 - 2600	200 - 2600
Length range	-	up to 6m	up to 6m
Locations	UK Ireland Netherlands Germany France Spain Sweden Norway Finland	UK Ireland Netherlands Germany France Spain Sweden Norway Finland	UK Netherlands

For further information please visit our service centre webpages.

EN-Product-Metallic coated-Structural steel-DownloadsTSUK

Download

Download:

EN-Engineering-Brochure-MagiZinc

MagiZinc - Brochure

Brochure

English

MagiZinc for superior corrosion protection

tata-steel-engineering-magizinc-corrosion-protection-brochure-en.pdf13.86 MB

EN-Product-Metallic coated-Structural steel-S450GD+Z/+ZM TSUK

S450GD+Z/+ZM

Specification details for S450GD+Z/+ZM

EN-Product-Metallic coated-Structural steel-All Grades OverviewTSUK

Overview

Relationship with standards

Galvanised structural steel complies with the following European standard

EN 10346: 2015
Grade
S220GD+Z/+ZM
S250GD+Z/+ZM
S280GD+Z/+ZM
S320GD+Z/+ZM
S350GD+Z/+ZM
S390GD+Z/+ZM
S420GD+Z/+ZM
S450GD+Z/+ZM
S550GD+Z

For products produced in the Netherlands click here.

EN-Product-Metallic coated-All Grades Coatings Surface aspectsTSUK

Coatings and surface aspects

Coatings

Three types of metallic coating are available:

Pure zinc

Galvanised steel (Z/GI) is coated with an almost pure zinc coating (>99% zinc).

Zinc-iron alloy

Produced in the Netherlands. For further information click here.

MagiZinc

MagiZinc steel (ZM) is coated with a zinc coating containing additional magnesium and aluminium.

Coating weight

Coating	Minimum	Maximum
Pure zinc (Z/GI)	90 (6 µm/side)	275 (20 µm/side)
MagiZinc (ZM)¹	70 (5 µm/side)	310 (22 µm/side)

Coating weight measured in g/m² double-sided (µm, per side).

Surface quality

Surface quality complies with standard: EN 10346:2015. Galvanised steels are available in surface quality A, B or C.
Also, Serica FLO^®surface quality produced in the Netherlands. For further information click here.

Surface quality A: as coated surface

Imperfections such as pimples, marks, scratches, pits, variations in surface appearance, dark spots, stripe marks and light passivation stains are permissible.
Stretch levelling breaks or run-off marks may appear. Coil breaks and stretcher strains may also appear.

Surface quality B: improved surface

With this surface quality, small imperfections such as stretch levelling breaks, skin pass marks, slight scratches, indentations, surface structure, zinc run-off marks and light passivation stains are permissible.

Surface quality C: best quality surface

Surface condition C is obtained by skin passing. The controlled surface for the exposed side enables application of a uniform paint finish. The reverse surface has, at least, the characteristics of surface quality B.

Surface finish

Pure zinc

MA: minimised spangle, as coated surface (Z/GI).
MB: minimised spangle, improved surface (Z/GI).
MC: minimised spangle, best quality surface (Z/GI).

MagiZinc^®

A : as coated surface (ZM).
B : improved surface (ZM).
C: best quality surface (ZM).

Surface roughness

Metallic coated steel (with the exception of galvanised steel with standard surface (MA) can be supplied in various grades of roughness – please contact us for more details. If no roughness is specified, roughness will be as shown in the table below.

Roughness Ra (µm)
cut off 0.8mm	cut off 2.5mm
0.6 - 1.9	0.7 - 2.2

Surface treatments

The surface treatments available are O, C and CO.

Oiling (O)

The material surface can be oiled with preservative oil. Other types of oil - for increasing strength or reducing weight – are available to help achieve your optimum performance parameters. Please contact us for details.

Tata Steel offers the following range of oiling levels:

Coating type	Capability
Pure zinc (Z/GI)	0.5 - 1.6 g/m²
MagiZinc^® (ZM)	0.5 - 1.6 g/m²

Other oiling levels are available on request.

Chromium-free passivation (C)

This surface treatment temporarily protects the zinc-coated material against white rust during transportation and storage (not applicable to all qualities and dimensions – please contact us for details).

Chromium-free passivation and oiled (CO)

Please request this combination of surface treatments if you require extra protection against white rust formation (not applicable to all qualities and dimensions – please contact us for details).

T-treatment

Please contact us for further information.

Prime Lubrication Treatment (PLT)

Prime Lubrication Treatment facilitates the manufacturing of stamped components by minimising known issues in stamping and joining.
Currently Under development, please contact us regarding further information

Untreated (U)

Please contact us regarding the availability of untreated coils.

EN-Product-Metallic Coated-Structural steel-S450GD-Properties TSUK

Properties

Mechanical properties

Metallic coated structural steel grades have the following mechanical properties (skin-passed) - these are measured longitudinal to the rolling direction:

EN 10346: 2015	Grade	S450GD+Z/+ZM
Min. yield strength Rp_0.2	N/mm²	450
Min. tensile strength R_m	N/mm²	510
Elongation	%	14

If the yield point is pronounced, the values apply to the upper yield point R_eH.
A range of 140 N/mm² can be expected for tensile strength.
Elongation after fracture uses test piece length L₀ = 80 mm.
For a thickness t ≤ 0.7 mm the minimum elongation after fracture is decreased by 2% and for a thickness t ≤ 0.5mm the minimum elongation after fracture is decreased by 4%.

Chemical composition

Tata Steel supplies the following cast analysis with maximum values unless otherwise shown:

EN 10346: 2015	Grade	S450GD+Z/+ZM
C	Max.	0.20
Si	Max.	0.60
Mn	Max.	1.70
P	Max.	0.10
S	Max.	0.045
Si	Max.	0.60

All values in weight%.

EN-Product-Metallic Coated-Structural steel-S450GD-Dimensions TSUK

Dimensions

Dimensional capability

Galvanised (+Z) products

Dimensions in mm.

Thickness	Max. width
From - up to	S450GD
0.70 - 1.00	1250
1.00 - 1.20	1300
1.20 - 1.40	1330
1.40 - 1.70	1360
1.70 - 2.00	1399

For widths below 900 mm, please contact us.
For products produced in the Netherlands click here.

MagiZinc^® (+ZM) products

Dimensions in mm.

Thickness	Max. width
From - up to	S450GD
0.70 - 1.00	1250
1.00 - 1.40	1300
1.40 - 1.70	1360
1.70 - 2.00	1399

For widths below 1100 mm please contact us.
For products produced in the Netherlands click here.

Tolerances

Tolerances comply with standard EN 10143: 2006.
Tighter tolerances are available - please contact us for details.

EN-Product-Metallic Coated-All Grades Shape and Dimensional TolerancesTSUK

Shape and dimensional tolerances

Tolerances on thickness

The tolerances comply with standard EN 10143: 2006.
Tighter tolerances are available on request.
Thickness tolerance availability is shown below:

Thickness tolerance	Availability
Full thickness tolerance	Available
Special thickness tolerance	Available
50% of full thickness tolerance	Refer before ordering

The following tolerances apply to the grades with a minimum value for the yield strength lower than 260N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
> 0.40	≤ 0.60	± 0.04	± 0.05	± 0.06	± 0.035	± 0.040	± 0.045
> 0.60	≤ 0.80	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.80	≤ 1.00	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 1.00	≤ 1.20	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.20	≤ 1.60	± 0.10	± 0.11	± 0.12	± 0.060	± 0.070	± 0.080
> 1.60	≤ 2.00	± 0.12	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 2.00	≤ 2.50	± 0.14	± 0.15	± 0.16	± 0.090	± 0.100	± 0.110
> 2.50	≤ 3.00	± 0.17	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130
> 3.00	≤ 5.00	± 0.20	± 0.20	± 0.21	± 0.15	± 0.16	± 0.17
> 5.00	≤ 6.50	± 0.22	± 0.22	± 0.23	± 0.17	± 0.18	± 0.19

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 260N/mm^² ≤ R_p0.2 < 360N/mm^² and for grades DX51D and S550GD.

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.035	± 0.040	-
> 0.40	≤ 0.60	± 0.05	± 0.06	± 0.07	± 0.040	± 0.045	± 0.050
> 0.60	≤ 0.80	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.80	≤ 1.00	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 1.00	≤ 1.20	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.20	≤ 1.60	± 0.11	± 0.13	± 0.14	± 0.070	± 0.080	± 0.090
> 1.60	≤ 2.00	± 0.14	± 0.15	± 0.16	± 0.080	± 0.090	± 0.110
> 2.00	≤ 2.50	± 0.16	± 0.17	± 0.18	± 0.110	± 0.120	± 0.130
> 2.50	≤ 3.00	± 0.19	± 0.20	± 0.20	± 0.130	± 0.140	± 0.150
> 3.00	≤ 5.00	± 0.22	± 0.24	± 0.25	± 0.17	± 0.18	± 0.19
> 5.00	≤ 6.50	± 0.24	± 0.25	± 0.26	± 0.19	± 0.20	± 0.21

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2.For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm

The following tolerances apply to the steel grades with a minimum value for the yield strength 360N/mm² ≤ R_p0.2 ≤ 420N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.05	± 0.06	-	± 0.040	± 0.045	-
> 0.40	≤ 0.60	± 0.06	± 0.07	± 0.08	± 0.045	± 0.050	± 0.060
> 0.60	≤ 0.80	± 0.07	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.80	≤ 1.00	± 0.08	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 1.00	≤ 1.20	± 0.10	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.20	≤ 1.60	± 0.13	± 0.14	± 0.16	± 0.080	± 0.090	± 0.110
> 1.60	≤ 2.00	± 0.16	± 0.17	± 0.19	± 0.090	± 0.110	± 0.120
> 2.00	≤ 2.50	± 0.18	± 0.20	± 0.21	± 0.120	± 0.130	± 0.140
> 2.50	≤ 3.00	± 0.22	± 0.22	± 0.23	± 0.140	± 0.150	± 0.160
> 3.00	≤ 5.00	± 0.22	± 0.24	± 0.25	± 0.17	± 0.18	± 0.19
> 5.00	≤ 6.50	± 0.24	± 0.25	± 0.26	± 0.19	± 0.20	± 0.21

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 420N/mm² < R_p0.2 ≤ 900N/mm².

Nominal thickness		Normal tolerances for a nominal width of ^{1 2}			Special tolerances (S) for a nominal width of ^{1 2}
		≤ 1200	> 1200	> 1500	≤ 1200	> 1200	> 1500
			≤ 1500			≤ 1500
≥ 0.35	≤ 0.40	± 0.06	± 0.07	-	± 0.045	± 0.050	-
> 0.40	≤ 0.60	± 0.06	± 0.08	± 0.09	± 0.050	± 0.060	± 0.070
> 0.60	≤ 0.80	± 0.07	± 0.09	± 0.11	± 0.060	± 0.070	± 0.080
> 0.80	≤ 1.00	± 0.09	± 0.11	± 0.12	± 0.070	± 0.080	± 0.090
> 1.00	≤ 1.20	± 0.11	± 0.13	± 0.14	± 0.080	± 0.090	± 0.110
> 1.20	≤ 1.60	± 0.15	± 0.16	± 0.18	± 0.090	± 0.110	± 0.120
> 1.60	≤ 2.00	± 0.18	± 0.19	± 0.21	± 0.110	± 0.120	± 0.140
> 2.00	≤ 2.50	± 0.21	± 0.22	± 0.24	± 0.140	± 0.150	± 0.170
> 2.50	≤ 3.00	± 0.24	± 0.25	± 0.26	± 0.170	± 0.180	± 0.190
> 3.00	≤ 5.00	± 0.26	± 0.27	± 0.28	± 0.23	± 0.24	± 0.26
> 5.00	≤ 6.50	± 0.28	± 0.29	± 0.30	± 0.25	± 0.26	± 0.28

_{^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed}
_{over a length of 15 metres.}
_{^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.}

Tolerances on width

The tolerances on width comply with standard EN 10143: 2006
MagiZinc is not included in the standard, but fulfils EN 10143: 2006 requirements.
Tighter tolerances are available on request.

Tolerances in mm.

Nominal width w	Normal tolerances	Special tolerances (S)
600 ≤ w ≤ 1200	+ 5 0	+ 2 0
1200 < w ≤ 1500	+ 6 0	+ 2 0
1500 < w ≤ 1800	+ 7 0	+ 3 0
w > 1800	+ 8 0	+ 3 0

Dimensions and coil weights

Description	Availability
Coil diameter inner	610mm
Coil diameter inner	(508 mm available on request)
Coil diameter outer	10/7 x width max
	1000mm min.
	2500mm max.
Coil weight	30t max.
	Coil weight limited by maximum outer diameter
	Maximum weight allowed by road/rail transport
	Some products may have different coil weight ranges available
	Usually a minimum coil weight up to 85% of the maximum coil weight can be requested
Minimum tonnage per order	Refer to price list for order quantity details
Minimum tonnage per order	Minimum order quantities may apply

EN-Product-Metallic coated-All grades Further processingTSUK

Further processing

We have a broad network of Tata Steel service centres across Europe, offering decoiling and slitting services from stock and against short lead times

Light gauge processing

Processing type	Slitting	Decoiling	Blanking
Thickness range (mm)	0.2 - 7.0	0.3 - 6.0	0.3 - 6.0
Width range (mm)	10 - 2050	50 - 2600	200 - 2600
Length range	-	up to 6m	up to 6m
Locations	UK Ireland Netherlands Germany France Spain Sweden Norway Finland	UK Ireland Netherlands Germany France Spain Sweden Norway Finland	UK Netherlands

For further information please visit our service centre webpages.

EN-Product-Metallic coated-Structural steel-DownloadsTSUK

Download

Download:

EN-Engineering-Brochure-MagiZinc

MagiZinc - Brochure

Brochure

English

MagiZinc for superior corrosion protection

tata-steel-engineering-magizinc-corrosion-protection-brochure-en.pdf13.86 MB

Structural steel

Tata Steel’s metallic coated structural steel behaves reliably in roll-forming and bending processes and is suitable for welding.

Applications

Relationship with standards

Coatings

Coating weight

Coating weight measured in g/m2 double-sided (µm, per side).

Surface quality

Surface finish

Surface roughness

Surface treatments

Properties

Mechanical properties

Chemical composition

All values in weight%.

Dimensional capability

Galvanised (+Z) products

For widths below 900 mm, please contact us.For products produced in the Netherlands click here.

MagiZinc® (+ZM) products

For widths below 900 mm please contact us.For products produced in the Netherlands click here.

Tolerances

Tolerances on thickness

The following tolerances apply to the grades with a minimum value for the yield strength lower than 260N/mm².

1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed over a length of 15 metres.2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 260N/mm² ≤ Rp0.2 < 360N/mm² and for grades DX51D and S550GD.

1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed over a length of 15 metres.2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm

The following tolerances apply to the steel grades with a minimum value for the yield strength 360N/mm² ≤ Rp0.2 ≤ 420N/mm².

1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed over a length of 15 metres.2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 420N/mm² < Rp0.2 ≤ 900N/mm².

1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed over a length of 15 metres.2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

Tolerances on width

Dimensions and coil weights

Further processing

Light gauge processing

For further information please visit our service centre webpages.

Download:

MagiZinc - Brochure

Relationship with standards

Coatings

Coating weight

Coating weight measured in g/m2 double-sided (µm, per side).

Surface quality

Surface finish

Surface roughness

Surface treatments

Properties

Mechanical properties

Chemical composition

All values in weight%.

Dimensional capability

Galvanised (+Z) products

For widths below 900 mm, please contact us.For products produced in the Netherlands click here.

MagiZinc® (+ZM) products

For widths below 900 mm please contact us.For products produced in the Netherlands click here.

Tolerances

Tolerances on thickness

The following tolerances apply to the grades with a minimum value for the yield strength lower than 260N/mm².

1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed over a length of 15 metres.2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 260N/mm² ≤ Rp0.2 < 360N/mm² and for grades DX51D and S550GD.

1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed over a length of 15 metres.2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm

The following tolerances apply to the steel grades with a minimum value for the yield strength 360N/mm² ≤ Rp0.2 ≤ 420N/mm².

1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed over a length of 15 metres.2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 420N/mm² < Rp0.2 ≤ 900N/mm².

1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed over a length of 15 metres.2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

Tolerances on width

Dimensions and coil weights

Further processing

Light gauge processing

For further information please visit our service centre webpages.

Download:

MagiZinc - Brochure

Relationship with standards

Coatings

Coating weight

Coating weight measured in g/m2 double-sided (µm, per side).

Surface quality

Surface finish

Surface roughness

Surface treatments

Properties

Coating weight measured in g/m² double-sided (µm, per side).

For widths below 900 mm, please contact us.
For products produced in the Netherlands click here.

MagiZinc^® (+ZM) products

For widths below 900 mm please contact us.
For products produced in the Netherlands click here.

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 260N/mm^² ≤ R_p0.2 < 360N/mm^² and for grades DX51D and S550GD.

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2.For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm

The following tolerances apply to the steel grades with a minimum value for the yield strength 360N/mm² ≤ R_p0.2 ≤ 420N/mm².

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 420N/mm² < R_p0.2 ≤ 900N/mm².

_{^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed}
_{over a length of 15 metres.}
_{^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.}

Coating weight measured in g/m² double-sided (µm, per side).

For widths below 900 mm, please contact us.
For products produced in the Netherlands click here.

MagiZinc^® (+ZM) products

For widths below 900 mm please contact us.
For products produced in the Netherlands click here.

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 260N/mm^² ≤ R_p0.2 < 360N/mm^² and for grades DX51D and S550GD.

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2.For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm

The following tolerances apply to the steel grades with a minimum value for the yield strength 360N/mm² ≤ R_p0.2 ≤ 420N/mm².

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 420N/mm² < R_p0.2 ≤ 900N/mm².

_{^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed}
_{over a length of 15 metres.}
_{^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.}

Coating weight measured in g/m² double-sided (µm, per side).

For widths below 900 mm, please contact us.
For products produced in the Netherlands click here.

MagiZinc^® (+ZM) products

For widths below 900 mm, please contact us.
For products produced in the Netherlands click here.

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 260N/mm^² ≤ R_p0.2 < 360N/mm^² and for grades DX51D and S550GD.

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2.For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm

The following tolerances apply to the steel grades with a minimum value for the yield strength 360N/mm² ≤ R_p0.2 ≤ 420N/mm².

^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed
over a length of 15 metres.
^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.

The following tolerances apply to the steel grades with a minimum value for the yield strength 420N/mm² < R_p0.2 ≤ 900N/mm².

_{^1. Around cold-rolled welds an increase of 20% at the most over the thickness tolerance is allowed}
_{over a length of 15 metres.}
_{^2. For zinc coatings ≥ Z450 the tolerance on the thickness must be raised by 0.02mm.}

Coating weight measured in g/m² double-sided (µm, per side).